BLM18AG471SH1D Murata, BLM18AG471SH1D Datasheet - Page 66

• Manufacturer Part Number: BLM18AG471SH1D
• Description: EMI/RFI Suppressors & Ferrites 0603 470ohms Gen Use Tape
• Manufacturer: Murata
• Series: BLM Ar

Specifications of BLM18AG471SH1D

• Shielding: Unshielded
• Test Frequency: 100 MHz
• Product: Chip Ferrite Beads
• Impedance: 470 Ohms
• Tolerance: 25 %
• Maximum Dc Current: 200 mAmps
• Maximum Dc Resistance: 0.5 Ohms
• Operating Temperature Range: - 55 C to + 125 C
• Package / Case: 0603 (1608 metric)
• Termination Style: SMD/SMT
• Frequency Range: 30MHz To 100MHz
• Dc Resistance Max: 0.35ohm
• Dc Current Rating: 500mA
• Ferrite Mounting: SMD
• Ferrite Case Style: 0603 / 1608
• Operating Temperature Min: -55°C
• Rohs Compliant: Yes
• Operating Temperature Max: +125°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

4
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
1. Do not use products beyond the rated current and rated
2. Be sure to provide an appropriate fail-safe
1. Self-heating
2. Mounting Direction
< Operating Environment >
Do not use products in a chemical atmosphere such as
chlorine gas, acid or sulfide gas.
< Storage and Handling Requirements >
1. Storage Period
1. Washing
2. Soldering
3. Mounting on-boad with Conductive Glue
64
Chip EMIFILr!Caution/Notice
voltage as this may create excessive heat and
deteriorate the insulation resistance.
function on your product to prevent a second damage
that may be caused by the abnormal function or
the failure our product.
BLM series should be used within 6 months, the
other series should be used within 12 months.
Products to be used after this period should be
checked for solderability or bondability with
glue.
Failure and degradation of a product are caused
by the washing method. When you wash in conditions
!Caution (Rating)
!Caution (Soldering and Mounting)
Notice (Storage and Operating Condition)
Notice (Soldering and Mounting)
that are not in mounting information, please contact
Murata engineering.
Reliability decreases with improper soldering
methods. Please solder by the standard soldering
conditions shown in mounting information.
BLM18AG_WH is designed for conductive glue
mounting method. Please refer to Mounting
infomation.
Please provide special attention when mounting chip
"EMIFIL" (BLM_P) series in close proximity to other
products that radiate heat.
The heat generated by other products may deteriorate
the insulation resistance and cause excessive heat in this
component.
Mount Chip Common Mode Choke Coils (DLW31S/43S)
in right direction. Wrong direction, which is 90 degrees
rotated from right direction, causes not only open or short
circuit but also flames or other serious trouble.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
2. Storage Conditions
4. Other
(1) Storage temperature: -10 to 40 degrees C
(2) Do not store products in a chemical atmosphere
Noise suppression levels resulting from Murata's
EMI suppression filters "EMIFIL" may vary,
depending on the circuits and ICs used, type of
noise, mounting pattern, mounting location, and
other operating conditions. Be sure to check and
confirm in advance the noise suppression effect
of each filter, in actual circuits, etc. before
applying the filter in a commercial-purpose
equipment design.
Relative humidity: 30 to 70%
Avoid sudden changes in temperature and humidity.
such as chlorine gas, acid or sulfide gas.
right direction
Z
wrong direction
Z
C50E.pdf
08.8.28