DEBB33A102KN2A Murata, DEBB33A102KN2A Datasheet - Page 34
![Ceramic Disc Capacitors 1000pF 1000volts B 10%](/photos/16/29/162974/mkvp3_sml.jpg)
DEBB33A102KN2A
Manufacturer Part Number
DEBB33A102KN2A
Description
Ceramic Disc Capacitors 1000pF 1000volts B 10%
Manufacturer
Murata
Series
DEBr
Specifications of DEBB33A102KN2A
Voltage Rating
1 KVolts
Operating Temperature Range
- 25 C to + 85 C
Termination Style
Radial
Product
High Voltage Ceramic Disc Capacitors
Dimensions
6 mm Dia.
Capacitance
1000 pF
Tolerance
10 %
Temperature Coefficient
B
Lead Spacing
5 mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DEBB33A102KN2A
Manufacturer:
MURATA
Quantity:
6 000
Company:
Part Number:
DEBB33A102KN2A
Manufacturer:
MURATA
Quantity:
33 000
6
!Note
32
No.
10
11 Solderability of Leads
12
* "Room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
DES Series (125 C Guaranteed / Low-dissipation Factor / DC500V-1kV) Specifications and Test Methods
DES Series Specifications and Test Methods
1
2
3
4
5
6
7
8
9
Operating Temperature Range
Appearance and Dimensions
Marking
Dielectric
Strength
Insulation
Resistance (I.R.)
Capacitance
Dissipation Factor (D.F.)
Temperature Characteristics
Strength of Lead
Vibration
Resistance
Soldering Effect
(Non-Preheat)
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
Item
Between Lead
Wires
Body Insulation
Between Lead
Wires
Pull
Bending
Appearance
Capacitance
D.F.
Appearance
Capacitance
Change
Dielectric Strength
(Between Lead
Wires)
-25 to +125°C
No visible defect, and dimensions are
within specified range.
To be easily legible
No failure
No failure
10000MΩ min.
Within specified tolerance
0.3% max.
Within +20/-30%
(Temp. range: -25 to +125°C)
Pre-treatment: Capacitor should be stored at 125±3°C for 1 hr., then placed at
Lead wire should not be cut off.
Capacitor should not be broken.
No marked defect
Within specified tolerance
0.3% max.
Lead wire should be soldered with
uniform coating on the axial direction
over 3/4 of the circumferential direction.
No marked defect
Within ±10%
Per item 4.
Specifications
room condition* for 24±2 hrs. before measurements.
Temp. (°C)
Step
20±2
1
-25±3
The capacitor should be visually inspected for evidence of
defect.
Dimensions should be measured with slide calipers.
The capacitor should be visually inspected.
The capacitor should not be damaged when DC voltage of
200% of the rated voltage (DC1kV) or DC voltage of 250% of
the rated voltage (DC500V) is applied between the lead wires
for 1 to 5 sec.
(Charge/Discharge currentV50mA)
The capacitor is placed in the container with
metal balls of diameter 1mm so that each
lead wire, short circuited, is kept about 2mm
off the metal balls as shown in the figure at
right, and AC1250V(r.m.s.) <50/60Hz> is
applied for 1 to 5 sec. between capacitor
lead wires and metal balls.
(Charge/Discharge currentV50mA)
The insulation resistance should be measured with
DC500±50V within 60±5 sec. of charging.
The capacitance should be measured at 20°C with 1±0.2kHz
and AC5V(r.m.s.) max.
The dissipation factor should be measured at 20°C with
1±0.2kHz and AC5V(r.m.s.) max.
The capacitance measurement should be made at each step
specified in the Table.
As shown in the figure at right, fix the body of
the capacitor and apply a tensile weight
gradually to each lead wire in the radial
direction of the capacitor up to 10N and keep
it for 10±1 sec.
Each lead wire should be subjected to 5N of weight and bent
90° at the point of egress, in one direction, then returned to its
original position and bent 90° in the opposite direction at the
rate of one bend in 2 to 3 sec.
The capacitor should be firmly soldered to the supporting lead
wire and vibrated at a frequency range of 10 to 55Hz, 1.5mm in
total amplitude, with about a 1-minute rate of vibration change
from 10Hz to 55Hz and back to 10Hz. Apply for a total of 6 hrs.,
2 hrs. each in 3 mutually perpendicular directions.
The lead wire of a capacitor should be dipped into a ethanol
solution of 25wt% rosin and then into molten solder for 2±0.5
sec. In both cases the depth of dipping is up to about 1.5 to
2mm from the root of lead wires.
Temp. of solder: Lead Free Solder (Sn-3Ag-0.5Cu) 245±5°C
The lead wire should be immersed into the melted solder of
350±10°C up to about 1.5 to 2mm from the main body for
3.5±0.5 sec.
Pre-treatment:
Post-treatment:
2
Capacitor should be stored at 125±3°C for 1 hr., then placed
at room condition* for 24±2 hrs. before initial measurements.
Capacitor should be stored for 24±2 hrs. at room condition.*
20±2
3
H63 Eutectic Solder 235±5°C
125±2
4
Test Method
20±2
5
Continued on the following page.
W
Metal balls
About 2mm
C85E.pdf
Jul.13,2011