GNM214R71E222MA01D Murata, GNM214R71E222MA01D Datasheet - Page 2

• Manufacturer Part Number: GNM214R71E222MA01D
• Description: Capacitor Arrays & Networks 4 Cap Array 0805 X7R 25V 2200pF
• Manufacturer: Murata
• Series: GNMr

Specifications of GNM214R71E222MA01D

• Voltage Rating: 25 Volts
• Number Of Elements: 4
• Operating Temperature Range: - 55 C to + 125 C
• Termination Style: SMD/SMT
• Dimensions: 2 mm L x 1.25 mm W x 0.6 mm H
• Dissipation Factor Df: 0.025
• Product: Ceramic Capacitor Arrays
• Capacitance: 2200 pF
• Tolerance: 20 %
• Temperature Coefficient: X7R
• Package / Case: 0805
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

No.
11
12
13
14
GNM Series Specifications and Test Method (1)
Continued from the preceding page.
Vibration
Resistance
Resistance to
Soldering Heat
Deflection
Solderability of
Termination
Item
Appearance
Capacitance
Q/D.F.
Appearance
Capacitance
Change
Q/D.F.
I.R.
Dielectric
Strength
No defects or abnormalities
Within the specified tolerance
30pF min.: QU1000
30pF max.:
C: Nominal
No cracking or marking defects should occur.
75% of the terminations are to be soldered evenly and
continuously.
The measured and observed characteristics should satisfy the
specifications in the following table.
No marking defects
Within T2.5%
(Whichever is
larger)
30pF min.: QU1000
30pF max.:
C: Nominal
More than 10,000MΩ or 500Ω · F (Whichever is smaller)
No failure
Compensating Type
#GNMpp4
Capacitance (pF)
Capacitance (pF)
Temperature
GNM0M2
GNM1M2
GNM212
GNM214
GNM314
QU400+20C
or T0.25pF
QU400+20C
Type
5.0
d
a
b
c
100
1.0
2.0T0.05
2.0T0.05
2.0T0.05
2.0T0.05
2.5T0.05
R7, R6: Within T7.5%
R7, R6
R7, R6
Char.
Char.
a
Specifications
Fig. 2
0.2T0.05
0.5T0.05
0.6T0.05
0.7T0.05
0.8T0.05
25V min.
25V min.
0.025
0.025
max.
max.
High Dielectric Type
#GNMpp2
b
5.0
0.035
0.035
d
max.
0.32T0.05
max.
a
b
16V
16V
0.2T0.05
0.5T0.05
0.3T0.05
0.4T0.05
c
c
100
1.0
0.035
0.035
max.
max.
10V
10V
0.25T0.05
0.32T0.05
0.5T0.05
0.2T0.05
0.4T0.05
t=0.8mm
(in mm)
d
max.
max.
6.3V
0.05
6.3V
0.05
Solder the capacitor to the test jig (glass epoxy board) in the
same manner and under the same conditions as (10). The
capacitor should be subjected to a simple harmonic motion
having a total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 55Hz. The
frequency range, from 10 to 55Hz and return to 10Hz, should
be traversed in approximately 1 minute. This motion should be
applied for a period of 2 hours in each of 3 mutually perpendic-
ular directions (total of 6 hours).
Solder the capacitor on the test jig (glass epoxy board) shown
in Fig. 2 using a eutectic solder.
Then apply a force in the direction shown in Fig. 3 for 5T1 sec.
The soldering should be done by the reflow method and should
be conducted with care so that the soldering is uniform and free
of defects such as heat shock.
Immerse the capacitor in a solution of ethanol (JIS-K-8101) and
rosin (JIS-K-5902) (25% rosin in weight proportion). Preheat at
80 to 120°C for 10 to 30 seconds. After preheating, immerse in
eutectic solder solution for 2T0.5 seconds at 230T5°C or
Sn-3.0Ag-0.5Cu solder solution for 2T0.5 seconds at 245T5°C.
Preheat the capacitor at 120 to 150°C for 1 minute. Immerse
the capacitor in a eutectic solder or Sn-3.0Ag-0.5Cu solder
solution at 270T5°C for 10T0.5 seconds. Let sit at room
temperature for 24T2 hours, then measure.
• Initial measurement for high dielectric constant type
Perform a heat treatment at 150+0/-10°C for one hour and
then let sit for 24T2 hours at room temperature.
Perform the initial measurement.
R230
Capacitance meter
45
Test Method
20
Fig. 3
50
Continued on the following page.
45
Pressurize
Pressurizing
speed : 1.0mm/sec.
Flexure : V1