B43505A5337M EPCOS Inc, B43505A5337M Datasheet - Page 17
![Aluminum Electrolytic Capacitors - Snap In AL-ELKO SNAP IN 330UF 450V](/photos/16/29/162913/epcossnap-in_sml.jpg)
B43505A5337M
Manufacturer Part Number
B43505A5337M
Description
Aluminum Electrolytic Capacitors - Snap In AL-ELKO SNAP IN 330UF 450V
Manufacturer
EPCOS Inc
Series
B43505r
Datasheet
1.B43505A5157M000.pdf
(21 pages)
Specifications of B43505A5337M
Esr
410 mOhms
Operating Temperature Range
- 40 C to + 105 C
Diameter
35 mm
Length
50 mm
Product
Aluminum Electrolytic Capacitors
Number Of Pins
3
Termination Style
Snap In
Test Frequency
100 Hz
Capacitance
330 uF
Tolerance
20 %
Voltage Rating
450 Volts
Lead Spacing
10 mm
Load Life
5000 Hrs
Ripple Current
1.8 Amps
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
B43505A5337M000
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
B43505A5337M000
Manufacturer:
EPCOS
Quantity:
30 000
Company:
Part Number:
B43505A5337M007
Manufacturer:
EPCOS
Quantity:
30 000
Company:
Part Number:
B43505A5337M060
Manufacturer:
EPCOS
Quantity:
30 000
Company:
Part Number:
B43505A5337M067
Manufacturer:
EPCOS
Quantity:
30 000
Company:
Part Number:
B43505A5337M080
Manufacturer:
EPCOS
Quantity:
30 000
Product safety
The table below summarize the safety instructions that must be observed without fail. A detailed
description can be found in the relevant sections of chapter "General technical information".
Topic
Polarity
Reverse voltage
Upper category
temperature
Maintenance
Mounting
position of screw
terminal capacitors
Mounting of
single-ended
capacitors
Robustness of
terminals
Soldering
Please read Cautions and warnings and
Important notes at the end of this document.
Safety information
Make sure that polar capacitors are connected
with the right polarity.
Voltages polarity classes should be prevented by
connecting a diode.
Do not exceed the upper category temperatur.
Make periodic inspections of the capacitors.
Before the inspection, make sure that the power
supply is turned off and carefully discharge the
electricity of the capacitors.
Do not apply any mechanical stress to the
capacitor terminals.
Do not mount the capacitor with the terminals
(safety vent) upside down.
The internal structure of single-ended capacitors
might be damaged if excessive force is applied to
the lead wires.
Avoid any compressive, tensile or flexural stress.
Do not move the capacitor after soldering to PC
board.
Do not pick up the PC board by the soldered
capacitor.
Do not insert the capacitor on the PC board with a
hole space different to the lead space specified.
The following maximum tightening torques must
not be exceeded when connecting screw
terminals:
M5: 2 Nm
M6: 2.5 Nm
Do not exceed the specified time or temperature
limits during soldering.
Page 17 of 21
Excellent performance
B41505, B43505
Reference
Chapter "General
technical information"
1
"Basic construction of
aluminum electrolytic
capacitors"
3.1.6
"Reverse voltage"
7.2
"Maximum permissible
operating temperature"
10
"Maintenance"
11.1
"Mounting positions of
capacitors with screw
terminals"
11.4
"Mounting
considerations for
single-ended capacitors"
11.3
"Mounting torques"
11.5
"Soldering"
105 C