B41112B7476M000 EPCOS Inc, B41112B7476M000 Datasheet - Page 15

• Manufacturer Part Number: B41112B7476M000
• Description: Aluminum Electrolytic Capacitors - SMD 35volts 47uF SMD 6.3x7.7mm 2000hr
• Manufacturer: EPCOS Inc

Specifications of B41112B7476M000

• Operating Temperature Range: - 40 C to + 85 C
• Dimensions: 6.3 mm Dia. x 7.7 mm L x 6.6 mm H
• Product: General Purpose Electrolytic Capacitors
• Dissipation Factor Df: 0.16
• Leakage Current: 3 uAmps
• Load Life: 2000 Hrs
• Termination Style: SMD/SMT
• Capacitance: 47 uF
• Tolerance: 20 %
• Voltage Rating: 35 Volts
• Lead Spacing: 2.2 mm
• Ripple Current: 77 mAmps
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Cautions and warnings
General
1
2
3
4
5
6
7
8
9
10 Manual soldering:
Please read Cautions and warnings and
Important notes at the end of this document.
Aluminum electrolytic capacitors have a bi-polar structure. This is marked on the body of the
capacitor. A capacitor must not be mounted with reversed polarity. The application of an AC
or reverse voltage may cause a short circuit or damage the capacitor. Bi-polar capacitors
must not be used in AC applications, where the polarity may be reversed in the circuits or is
unknown.
The DC voltage applied to the capacitor terminal must not exceed its rated operating voltage,
as this will result in a rapid increase of the leakage current and may damage the capacitor. It
is recommended to operate the capacitor at 70 – 80% of its rated voltage to optimize its
service life.
The ripple current applied to the capacitor must be within the permitted range. An excessive
ripple current leads to impaired electrical properties and may damage the capacitor. Note
that the sum of the peak values of the ripple voltage and the DC operating voltage must not
exceed the rated DC voltage.
Capacitors must be used within their permitted range of operating temperature. Operation at
room temperature optimizes their service life.
Capacitors with case diameter 8 mm are equipped with a safety vent. In capacitors fitted
with a lead or soldering lug, the safety vent is usually located at the base of the case. It
needs sufficient space around it to operate optimally. The following dimensions are
recommended: for case diameter d = 8 to 16 mm, more than 2 mm; for d = 18 to 35 mm,
more than 3 mm; and for d = 42 mm or more, more than 5 mm.
Capacitors should not be mounted with the safety vent face down on the board. Do not
locate any wire or copper trace near the safety vent. Do not reverse the voltage, as this may
result in excess pressure and the leakage of electrolyte.
Gas is released through the safety vent when the pressure inside the capacitor is too high. A
gaseous liquid around the safety vent does not indicate a leakage of electrolyte.
The capacitor should be stored under conditions of normal temperature and in a non-acid,
non-alkali environment of normal humidity. Exposure to high temperatures, for example
under direct sunlight, will reduce its operating life. If the capacitor is stored in an environment
containing acids or alkalis, the solderability of the leads may be affected.
containing acids or alkalis, the solderability of the leads may be affected.The leakage current
of an aluminum electrolytic capacitor may increase after a long period of storage. After such
storage, the capacitor must be aged by applying the rated operating voltage for 6 – 8 hours
before use.
a Soldering must be performed within the specified conditions.
b Ensure that the soldering iron does not touch any part of the capacitor body.
Bit temperature: 350 C; application time of soldering iron: 3 seconds.
Page 15 of 17
Standard series
B41112
85 C