SV01A103AEA01B00 Murata, SV01A103AEA01B00 Datasheet - Page 8

• Manufacturer Part Number: SV01A103AEA01B00
• Description: Board Mount Motion & Position Sensors 10K OHM SMD
• Manufacturer: Murata

Specifications of SV01A103AEA01B00

• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

1
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
1. Soldering profile for Lead-free solder (96.5Sn/3.0Ag/0.5Cu)
2. Soldering profile for Eutectic solder (63Sn/37Pb)
Uncontrolled mechanical force (except usual rotation on
the hollow rotor of product) may cause a change of
electrical characteristics, an increase of rotational
torque or mechanical damage of the product.
Therefore, please consider the following points
for your design.
1. Please make sure the connecting impedance is not
2. To minimize processing errors and rare cases of
6
SV01A
SV01
SV01 Series Notice
(Limit profile: refer to 1)
less than 1M ohm. The rotary position sensor
is designed to connect the output terminal and A/D
port of the microprocessor directly. Therefore,
connecting impedance presupposes certain M ohm and
the contact resistance is set high.
noise influence when data is installed,
please consider the following when programming
your software.
Soldering Profile
Notice (Handling)
Notice (Other)
Reflow Soldering Profile
Soldering Iron
Series
Series
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
T1
T1
150 to 180 60 to 120
Temp. (T1)
Temperature of Soldering Iron Tip
C
Pre-heating
t1
t1
T3
T2
T3
T2
Time (t1)
350 10
sec.
t2
t3
C
t2
Time (s)
Time (s)
Temp. (T2)
T5
T4
Standard Profile
220
Limit Profile
Standard Profile
Standard Profile
C
Heating
Time (t2)
30 to 60
sec.
Soldering Time
Temperature
3 max.
245 3
sec.
Peak
(T3)
SV01A
C
Series
Standard Condition
Cycle of
1. The product must be soldered by the terminals.
2. The connecting shaft must be sustained by the
3. Before using rotary position sensor, please test
4. MURATA cannot guarantee rotary position sensor
Reflow
Time
(1) Data install should be done plural times and
(2) Data considered as error should be invalid.
(3) If suspicious data is found, the data should be
Do not affix by screw clamping to support board
as this could cause mechanical deformation.
bearing. No uncontrolled force should be applied
to the hollow rotor.
after assembly in your particular mass production
system.
integrity when used under conditions other than
those specified in this document.
2
applied the mean value.
re-installed.
150 to 180 60 to 120
Temp. (T1)
Temp. (T1)
Soldering Iron Power Output
150
C
C
Pre-heating
Pre-heating
30 max.
60 to 120
Time (t1)
Time (t1)
sec.
sec.
W
Temp. (T4)
Temp. (T2)
Standard Profile
230
183
C
C
Limit Profile
Heating
Heating
Time (t3)
Time (t2)
30 to 50
sec.
sec.
30
Cycle of Soldering Iron
Temperature
Temperature
260 +5/-0
Time
Peak
Peak
1
230
(T5)
(T3)
C
C
Cycle of
Cycle of
Reflow
Reflow
Time
Time
2
1
R51E.pdf
09.3.26