MAX1479ATE+ Maxim Integrated Products, MAX1479ATE+ Datasheet - Page 7

• Manufacturer Part Number: MAX1479ATE+
• Description: RF Transmitter IC TRANSMITTER ASK/FSK
• Manufacturer: Maxim Integrated Products
• Type: Transmitterr

Specifications of MAX1479ATE+

• Operating Frequency: 450 MHz
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 2.5 V, 3.3 V
• Supply Current: 2.9 mA to 18.1 mA
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.1 V
• Package / Case: TQFN-16 EP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

The MAX1479 has a dedicated digital output pin for the
frequency-divided crystal clock signal. This is to be
used as the time base for a microprocessor. The fre-
quency-division ratio is programmable through two dig-
ital input pins (CLK0, CLK1), and is defined in Table 1.
The clock output is designed to drive a 3.5MHz CMOS
rail-to-rail signal into a 10pF capacitive load.
The envelope-shaping resistor allows for a gentle turn-
on/turn-off of the PA in ASK mode. This results in a small-
er spectral width of the modulated PA output signal.
The PLL block contains a phase detector, charge
pump, integrated loop filter, VCO, asynchronous 32x
clock divider, and crystal oscillator. The PLL requires
no external components. The relationship between the
carrier and crystal frequency is given by:
The crystal oscillator in the MAX1479 is designed to
present a capacitance of approximately 3pF to ground
from the XTAL1 and XTAL2 pins in ASK mode. In most
cases, this corresponds to a 4.5pF load capacitance
applied to the external crystal when typical PCB para-
sitics are added. In FSK mode, a percentage (defined
by bits DEV0 to DEV2) of the 3pF internal crystal oscil-
lator capacitance is removed for a logic 1 on the DIN
pin to pull the transmit frequency. The frequency devia-
tion is shown in Table 2. It is very important to use a
crystal with a load capacitance that is equal to the
capacitance of the MAX1479 crystal oscillator plus
PCB parasitics. If very large FSK frequency deviations
are desired, use a crystal with a larger motional capaci-
tance and/or reduce PCB parasitic capacitances.
The PA of the MAX1479 is a high-efficiency, open-drain,
switch-mode amplifier. With a proper output-matching
network, the PA can drive a wide range of impedances,
including small-loop PCB trace antennas and any 50Ω
antennas. The output-matching network for a 50Ω anten-
na is shown in the Typical Application Circuit . The out-
put-matching network suppresses the carrier harmonics
and transforms the antenna impedance to an optimal
impedance at PAOUT (pin 8), which is about 250Ω.
When the output-matching network is properly tuned,
the power amplifier is highly efficient. The Typical
Crystal-Based +10dBm ASK/FSK Transmitter
_______________________________________________________________________________________
f
Envelope-Shaping Resistor
XTAL
= f
RF
Phase-Locked Loop
/32
Crystal Oscillator
Power Amplifier
Clock Output
300MHz to 450MHz Low-Power,
Application Circuit delivers +10dBm at a supply volt-
age of +2.7V, and draws a supply current of 6.7mA for
ASK/OOK operation (V
10.5mA for FSK operation. Thus, the overall efficiency
at 100% duty cycle is 35%. The efficiency of the power
amplifier itself is about 50%. An external resistor at
ROUT sets the output power.
When matched to a 50Ω system, the MAX1479 PA is
capable of delivering more than +10dBm of output
power at V
drain transistor that requires external impedance
matching and pullup inductance for proper biasing.
The pullup inductance from PAOUT to V
main purposes: It forms a resonant tank circuit with the
capacitance of the PA output, provides biasing for the
PA, and becomes a high-frequency choke to reduce
the RF energy coupling into V
achieved when the PA drives a load of 250Ω. The rec-
ommended output-matching network topology is shown
in the Typical Application Circuit .
Table 1. Clock Divider Settings
Table 2. Frequency-Deviation Settings
DEV2
0
0
0
0
1
1
1
1
CLK1
0
0
1
1
DD
= 2.7V. The output of the PA is an open-
DEV1
Applications Information
0
0
1
1
0
0
1
1
Output Matching to 50 Ω
DIN
CLK0
0
1
0
1
DEV0
DD
at 50% duty cycle) and
0
1
0
1
0
1
0
1
. Maximum efficiency is
DD
DEVIATION
1/8 x max
1/4 x max
3/8 x max
1/2 x max
5/8 x max
3/4 x max
7/8 x max
CLKOUT
serves three
f
Logic 0
F
F
XTAL
Max
XTAL
XTAL
/16
/4
/8
7