FP2189-G TriQuint, FP2189-G Datasheet
FP2189-G
Specifications of FP2189-G
Available stocks
Related parts for FP2189-G
FP2189-G Summary of contents
Page 1
... W-CDMA Ch. Power 24 @ -45 dBc ACLR Drain Voltage +30 Drain Current +43 4.5 5. Typical parameters represent performance in a tuned application circuit. +8V @ 250 mA = 250 application circuit DQ Ordering Information Part No. FP2189-G FP2189-PCB900S FP2189-PCB1900S FP2189-PCB2140S Functional Diagram GND GND RF OUT Function Pin No. Input / Gate Output / Drain ...
Page 2
... FP2189 1-Watt HFET S-Parameters (V S21 and Maximum Stable Gain Frequency (GHz) Note: Measurements were made on the packaged device in a test fixture with 50 ohm input and output lines. The S-parameters shown are the de-embedded data down to the device leads and represents typical performance of the device. ...
Page 3
... FP2189 1-Watt HFET Application Circuit: 870 – 960 MHz (FP2189-PCB900S) Frequency S21 – Gain S11 – Input Return Loss S22 – Output Return Loss Output P1dB Output IP3 (+15 dBm / tone, 1 MHz spacing) Noise Figure IS-95 Channel Power @ -45 dBc ACPR CAP PORT ...
Page 4
... FP2189 1-Watt HFET FP2189-PCB900S Application Circuit Performance Plots S11 vs. Frequency 0 -40c +25c +85c -5 -10 -15 -20 -25 -30 860 880 900 920 940 Frequency (MHz) P1dB vs. Frequency -40c +25c +85c 24 860 880 900 920 940 Frequency (MHz) OIP3 vs. Temperature freq = 915, 916 MHz ...
Page 5
... FP2189 1-Watt HFET Application Circuit: 1930 – 1990 MHz (FP2189-PCB1900S) Frequency S21 – Gain S11 – Input Return Loss S22 – Output Return Loss Output P1dB Output IP3 (+15 dBm / tone, 1 MHz spacing) Noise Figure IS-95 Channel Power @ -45 dBc ACPR -Vgg RES ...
Page 6
... FP2189 1-Watt HFET FP2189-PCB1900S Application Circuit Performance Plots S11 vs. Frequency 0 -5 -10 -15 -20 -25 -40C +25C +85C -30 1930 1950 1970 Frequency (MHz) P1dB vs. Frequency -40c +25c +85c 24 1930 1950 1970 Frequency (MHz) OIP3 vs. Temperature freq = 1960, 1961 MHz +15 dBm / tone 36 -40 -15 10 ...
Page 7
... FP2189 1-Watt HFET Application Circuit: 2110 – 2170 MHz (FP2189-PCB2140S) Frequency S21 – Gain S11 – Input Return Loss S22 – Output Return Loss Output P1dB Output IP3 (+15 dBm / tone, 1 MHz spacing) Noise Figure W-CDMA Channel Power @ -45 dBc ACPR -Vgg RES ...
Page 8
... FP2189 1-Watt HFET FP2189-PCB2140S Application Circuit Performance Plots S11 vs. Frequency 0 -40c +25c +85c -5 -10 -15 -20 -25 -30 2110 2130 2150 Frequency (MHz) P1dB vs. Frequency -40C +25C +85C 24 2110 2130 2150 Frequency (MHz) OIP3 vs. Temperature freq = 2140, 2141 MHz +15 dBm / tone 36 -40 -15 10 ...
Page 9
... The 2.4 – 2.6 GHz Reference Circuit is shown for design purposes only. An evaluation board is not readily available for this application. The reader can obtain an FP2189-PCB2140S evaluation board and modify it with the circuit shown to achieve the performance shown in this reference design. CAP ...
Page 10
... The 3.4 – 3.6 GHz Reference Circuit is shown for design purposes only. An evaluation board is not readily available for this application. The reader can obtain an FP2189-PCB2140S evaluation board and modify it with the circuit shown to achieve the performance shown in this reference design. IND ...
Page 11
... The active-bias circuit, shown on the right, uses dual PNP transistors to provide a constant drain current into the FP2189, while also eliminating the effects of pinchoff variation. This configuration is best suited for applications where the intended output power level of the amplifier is backed off at least 6 dB away from its compression point ...
Page 12
... Land Pattern WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: sales@wj.com • Web site: www.wj.com, www.TriQuint.com Product Marking The FP2189-G will be marked with an “FP21G” designator. An alphanumeric lot code (“XXXX-X”) is also marked below the part designator on the top surface of the package ...