EN5394QI-E Enpirion, EN5394QI-E Datasheet
EN5394QI-E
Specifications of EN5394QI-E
Related parts for EN5394QI-E
EN5394QI-E Summary of contents
Page 1
... Thank you for choosing Enpirion, the source for Ultra small foot print power converter products. This user guide should be used together with the latest device datasheet. • The EN5364QI and EN5394QI (collectively referred to as EN53x4QI in the remainder of this document) features integrated inductor, power MOSFETS, Controller, bulk of the compensation Network, and protection circuitry against system faults ...
Page 2
... EN5364QI-EN5394QI Evaluation Board Application Note voltage may be coupled to the output via a diode. This diode (D2) is populated on the board. Back-feed voltage may be applied at BF_IN (TP18) Parallel Mode operation o operated in parallel when load currents greater than 6A/9A is desired. In parallel mode, one device is designated the Master and devices operate in slave mode, controlled by the Master ...
Page 3
... EN5364QI-EN5394QI Evaluation Board Application Note • The phase delay is set by connecting a resistor from S_delay to AGND. The delay is approximately: Delay (nsec) = 2*[S_delay resistance in kΩ.] A 49.9kΩ (populated on Evaluation board) resistor value delays the clock signal by ~100nsec. • EN53x4QI supports pre-bias mode operation. To use this option set the EN_PB jumper to pre-bias enable position with device powered down ...
Page 4
... EN5364QI-EN5394QI Evaluation Board Application Note Figure - 1 : Output voltage programming and loop compensation. R correspond R17 & C20 on the board. R R13, R14, R16, or R18 on the board, depending on which jumpers are populated on J13. 2.5V Rext 250 VIN AGND IC Package Quick Start Guide VIN SIDE Figure – ...
Page 5
... EN5364QI-EN5394QI Evaluation Board Application Note Figure – J13 Voltage Selection Jumpers In Figure 4, output Voltages, from left to right, are 0.804V, 0.998V, 1.2V and 1.0V.Jumper as shown, selects 1.2V output. Higher output voltages can be achieved by populating multiple J13 jumper positions. See Figures 1 and 7. CAUTION: Except for ENA, NONE of the J1 & ...
Page 6
... EN5364QI-EN5394QI Evaluation Board Application Note MAR-1 Float Low High Low High Low High Float Float Table-1 : Margin Block Truth Table STEP 7: Phase Lock – Disable device by moving ENA jumper. Power down the device. Connect a pulse generator (properly terminated and output disabled) signal between S_IN and GND. Set the pulse amplitude to swing from 0 to 2.5 volts. Set the pulse frequency to 4MHz. Connect oscilloscope probes to S_IN & ...
Page 7
... EN5364QI-EN5394QI Evaluation Board Application Note Figure – Evaluation Board Layout. Page November 2009 V_3 ...
Page 8
... EN5364QI and approximately 100uF for the EN5394QI. The board is populated with a 47uF, 1206, X5R and a 10uF, 0805, X7R capacitor for the EN5364QI and 2 x 47uF, 1206, X5R capacitor for the EN5394QI evaluation board. NOTE: Capacitors must be X5R or X7R dielectric formulations to ensure adequate capacitance over operating voltage and temperature ranges ...
Page 9
... EN5364QI-EN5394QI Evaluation Board Application Note AGND VFB AGND GND OUT R1 TP22 J10 VOUT TP19 R2 C10 TP7 TP6 R6 VSENSE J2 J3 AGND TP11 VOUT J7 VOUT TP18 Eval Board Input Protection PVIN S2A AGND Sync Delay Programming S_DEL Top turn pot R5 R10 AGND Figure – Evaluation Board Schematic ...
Page 10
... EN5364QI-EN5394QI Evaluation Board Application Note Contact Information Enpirion, Inc. Perryville III 53 Frontage Road, Suite 210 Hampton, NJ 08827 Phone: +1-908-894-6000 Fax: +1-908-894-6090 www.enpirion.com Enpirion reserves the right to make changes in circuit design and/or specifications at any time without notice. Information furnished by Enpirion is believed to be accurate and reliable. Enpirion assumes no responsibility for its use or for infringement of patents or other third party rights, which may result from its use ...