TSOP4838 Vishay, TSOP4838 Datasheet - Page 5
![Infrared Receivers 4.5-5.5V 38kHz](/photos/22/61/226174/4472390_sml.jpg)
TSOP4838
Manufacturer Part Number
TSOP4838
Description
Infrared Receivers 4.5-5.5V 38kHz
Manufacturer
Vishay
Specifications of TSOP4838
Carrier Frequency
38 KHz
Supply Current
0.85 mA
Beam Angle
45 deg
Data Transmission Rate
800 bits/s
Mounting Style
Through Hole
Transmission Distance
45 m
Viewing Angle
45 deg
Output Current
5 mA
Operating Voltage
2.7 V to 5.5 V
Power Dissipation
10 mW
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 25 C
Transmission Range
45m
Directivity
45°
Supply Voltage Range
2.7V To 5.5V
Opto Case Style
Through Hole
Operating Temperature Range
-25°C To +85°C
Svhc
No SVHC
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
TSOP4838
Manufacturer:
VISHAY/威世
Quantity:
20 000
Company:
Part Number:
TSOP4838LL1
Manufacturer:
WYC
Quantity:
23 470
Company:
Part Number:
TSOP4838SB1
Manufacturer:
VIS
Quantity:
1 353
Company:
Part Number:
TSOP4838SB1
Manufacturer:
ESIC
Quantity:
30 000
Company:
Part Number:
TSOP4838SJ1
Manufacturer:
FS
Quantity:
984
Company:
Part Number:
TSOP4838UH1
Manufacturer:
EPCOS
Quantity:
1 000
SUITABLE DATA FORMAT
These products are designed to suppress spurious output
pulses due to noise or disturbance signals. Data and
disturbance signals can be distinguished by the devices
according to carrier frequency, burst length and envelope
duty cycle. The data signal should be close to the
band-pass center frequency (e.g. 38 kHz) and fulfill the
conditions in the table below.
When a data signal is applied to the IR receiver in the
presence of a disturbance signal, the sensitivity of the
receiver is reduced to insure that no spurious pulses are
present at the output. Some examples of disturbance
signals which are suppressed are:
• DC light (e.g. from tungsten bulb or sunlight)
• Continuous signals at any frequency
• Modulated IR signals from common fluorescent lamps
Note
• For data formats with short bursts please see the datasheet of TSOP23.., TSOP43..
Document Number: 82090
Rev. 2.8, 04-Feb-11
Minimum burst length
After each burst of length
a minimum gap time is required of
For bursts greater than
a minimum gap time in the data stream is needed of
Maximum number of continuous short bursts/second
Recommended for NEC code
Recommended for RC5/RC6 code
Recommended for Sony code
Recommended for Thomson 56 kHz code
Recommended for Mitsubishi code
(38 kHz, preburst 8 ms, 16 bit)
Recommended for Sharp code
Suppression of interference from fluorescent lamps
(example of noise pattern is shown in fig. 14 or fig. 15)
IR Receiver Modules for Remote
TSOP22.., TSOP24.., TSOP48.., TSOP44..
Control Systems
Most common disturbance signals are
TSOP22.., TSOP48..
> 4 x burst length
10 cycles/burst
10 to 70 cycles
suppressed
12 cycles
70 cycles
800
yes
yes
yes
yes
yes
yes
16921
16920
Fig. 14 - IR Signal from Fluorescent Lamp
Fig. 15 - IR Signal from Fluorescent Lamp
0
0
with High Modulation
with Low Modulation
5
5
Vishay Semiconductors
Even extreme disturbance signals are
Time (ms)
Time (ms)
10
10
TSOP24.., TSOP44..
> 10 x burst length
10 cycles/burst
10 to 35 cycles
suppressed
12 cycles
35 cycles
15
15
1300
yes
yes
yes
yes
yes
no
www.vishay.com
20
20
5