MS27467T17B35S ITT Cannon, MS27467T17B35S Datasheet - Page 29
![no-image](/images/manufacturer_photos/0/3/349/itt_cannon_sml.jpg)
MS27467T17B35S
Manufacturer Part Number
MS27467T17B35S
Description
CONN PLUG 55POS STRAIGHT W/SCKT
Manufacturer
ITT Cannon
Series
Military, MIL-DTL-38999 Series I, KJLr
Datasheet
1.MS27656E11F35P.pdf
(32 pages)
Specifications of MS27467T17B35S
Connector Type
Plug, Female Sockets
Number Of Positions
55
Shell Size - Insert
17-35
Mounting Type
Free Hanging (In-Line)
Termination
Crimp
Fastening Type
Bayonet Lock
Orientation
N (Normal)
Ingress Protection
Environment Resistant
Shell Material, Finish
Aluminum, Olive Drab Cadmium Plated
Features
Shielded
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Shell Size, Military
-
Other names
IMS27467T17B35S
MS27467T17B35SPEI
MS27467T17B35SPEI
MS27467T17B35SPEI
MS27467T17B35SPEI
www.ittcannon.com
Dimensions shown in mm
Specifications and dimensions subject to change
A A s s s s e e m m b b l l y y I I n n s s t t r r u u c c t t i i o o n n s s
Wire Stripping
Strip insulation from end of wire to be crimped.
(See table for proper stripping dimensions.) Do not
cut or damage wire strands.
Contact Crimping
Contact Insertion
Contact Extraction
MIL-DTL-38999 Series I, II, III Connectors
1. Insert stripped wire into contact crimp pot.
Wire must be visible thru inspection hole.
1. Remove hardware from plug or receptacle and
slip over wire bundle in proper order for
reassembly.
4. Hold wire firmly in tool and extract wired
contact and tool. Repeat operation for all
contacts to be extracted.
1. Remove hardware from plug or receptacle
and slide hardware back along wire bundle.
VISUAL INSPECTION HOLE
2. Using correct crimp tool and locator, cycle the tool once to be sure the indentors are open. Insert
contact and wire into locator. Squeeze tool handles firmly and completely to insure a proper crimp. The
tool will not release unless the crimp indentors in the tool head have been fully actuated.
2. Using proper plastic or metal insertion tool for
corresponding contact, position wire in tip of the tool
so that the tool tip butts up against the contact
shoulder.
5. Fill any empty wire cavities with wire sealing plugs, and
4. Remove tool and pull back lightly on wire to make
sure contact is properly seated. Repeat operation with
remainder of contacts to be inserted, beginning with
the center cavity and working outward in alternating
rows.
2. Using plastic or metal extraction tool with proper
color code corresponding to contact size, place wire in
tool.
29
A
3. Release crimped contact and wire from tool. Be
certain the wire is visible thru inspection hole in
contact.
* For reference only
Cannon KJL/KJ/KJA
Wire Size
22D or 22M*
5. After all contacts are inserted, fill any empty
cavities with wire sealing plugs, Ressemble plug
or receptacle hardware.
3. Insert tool into contact cavity until tool tip
bottoms against the contact shoulder, expanding
clip retaining tines.
3. Press tool against contact shoulder and, with
firm and even pressure, insert wired contact and
tool tip into center contact cavity. A slight click may
be heard as metal retaining tines snap into place
behind contact shoulder.
6. Reassemble plug or receptacle.
20
16
12
.125 (3.18)
.188 (4.77)
.188 (4.77)
.188 (4.77)
A