025-0585-000 ITT Cannon, 025-0585-000 Datasheet - Page 63

• Manufacturer Part Number: 025-0585-000
• Description: RP DPD 33 & 34 DUST CAP
• Manufacturer: ITT Cannon

Specifications of 025-0585-000

• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: I025-0585-000

DPX*MA/ME Coaxial Contact Data (for environmental requirements)
www.ittcannon.com
ARINC 404
1. Use Crimp Tool No. DIE Y211 (995-0002-249), Tool M22520 / 5-01 (995-
2. Use extraction tool No. CET-C8. An insertion tool is not required.
3. Center contact, rear insulator, crimp ring, support bushing (not applicable to
4. Cable Assembly Instructions:
5. To extract: coaxial, push back seal sleeve and support bushing. Slip cable into ex-
A. Carefully push inner conductor through rear insulator.
B. While holding rear insulator firmly against ferrule, trim conductor to .156
C. Place contact over conductor and solder.
A. Push ferrule under braid as far as it will go. Trim off braid extending beyond
B. While holding ferrule in place pull crimp sleeve forward over braid until it is
C. Trim dielectric to the .035 (0.89)/.030 (0.76) dimension.
Components/Accessories
LITTLE CAESAR® CONTACT RETENTION (A32W4 & AW8 CONTACT ARRANGEMENTS)
Coaxial Contact Assembly and Extraction Recommendations
Without Seal†† (MA)
*P for Pin. S for Socket
Unsealed accommodates both Seal 1 & Seal 2 cables.
For use with connector supplied less grommet (Code-29**, etc.).
(See Note 5).
RG58/RG142 coaxials), seal sleeve, front insulator, shell and ferrule are
shipped unassembled in a common container.
Step 1 - If applicable, determine which portion of seal sleeve should be
used. If seal 2 is used, cut off seal 1 portion.
Step 2 - In sequence, place seal sleeve, support bushing and crimp ring
over cable jacket.
Step 3 - Trim cable per illustration.
Step 4 - Comb out braid and flare out ends to permit entry of ferrule.
Step 5 - Complete termination per illustration. (See below)
traction tool. Push tool into insert until it contacts coaxial retaining shoulder. Grip
both cable and tool with one hand and pull coaxial rearward out of insert cavity.
(3.96)/.146 (3.71) dimension.
shoulder of ferrule, if necessary.
tight against shoulder an ferrule. Pull firmly against face of ferrule to make
sure it is up tight.
0001-761).
P-249-1633-004
S-249-1634-003
P-249-1982-000
S-249-1983-000
P-249-2017-001
S-249-2018-001
P-249-2019-001
S-249-2020-001
P-249-2061-001
S-249-2062-001
Part Number*
P-249-1633-003
S-249-1634-002
P-249-1982-001
S-249-1983-001
P-249-2017-000
S-249-2018-000
P-249-2019-000
S-249-2020-000
P-249-2061-000
S-249-2062-000
Sealed (ME)
.035 (0.89)
.030 (0.76)
FERRULE
24
32
9
{
{
{
{
22
7
32W4** (MA Version)
A32W4 (ME Version)
15
RG180B
RG142B
RG178B
28
RG58C
RG179
Seal 1
31
Cable Accommodation†
.156 (3.96)
.146 (3.71)
REAR INSULATOR
30
CONTACT
10
25
RG174, RG316,
BRAID
16
1
29
RG179B
Seal 2
RG195
8
23
X
X
X
63
4
8
.158 (8.89)
.196 (4.98)
.075 (1.90)
.111 (2.82)
.196(4.98)
Size/Max.
A. Place front insulator over contact and then push assembly into coaxial shell.
B. Place parts in jaw of crimp tool. Locate jaws at start of chamfer on crimp
C. After assembled coaxial is inserted into connector, push support bushing into
6. To facilitate extraction of contacts and avoid splaying, the length of free cable
Ins. Dia.
W8** (MA Version)
AW8 (ME Version)
adjacent to the rear surface of the connector should not be less than 2.000
(50.80).
sleeve. Press sleeve firmly into coaxial shell and crimp.
grommet until shoulder rests on tubular extension. Then pull sealing sleeve
forward until it is snug on grommet.
6
2
WITHOUT SEAL
SOCKET
1
5
.350 (8.89)
.330 (8.38)
.260 (6.60)
.250 (6.35)
.260 (6.60)
.250 (6.35)
.260 (6.60)
.250 (6.35)
.260 (6.60)
.250 (6.35)
PIN
'A' Trim
Dim.
7
3
APPROX.
(8.89)
.350
SEAL 1
CRIMP AREA
SEAL 2
BUSHING
DPX*ME Crimp
SEAL
Cable Trim Dimensions
SOCKET
SEALED
SOCKET
PIN
.610 (15.49)
.590 (14.99)
PIN
A
FRONT INSULATOR
BUSHING
COAXIAL SHELL