025-0767-001 ITT Cannon, 025-0767-001 Datasheet - Page 103
025-0767-001
Manufacturer Part Number
025-0767-001
Description
RP CONDUCTIVE D/C 34 SHELL
Manufacturer
ITT Cannon
Datasheet
1.025-0767-001.pdf
(120 pages)
Specifications of 025-0767-001
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
I025-0767-001
- Current page: 103 of 120
- Download datasheet (3Mb)
Assembly Procedures
Dimensions shown in inch (mm)
Specifications and dimensions subject to change
www.ittcannon.com
Assembly Steps
Coaxial Contact Assembly (DPGM/DPJM)
1 . After the coaxial cable has been stripped to the
2. Assemble crimp ring under braid and add bush-
3. The center contact is supplied loose in the
Cable Stripping
proper dimensions, tin the center conductor. If
O.D. of cable is less than .096 (2.44), slip
rubber bushing over wire. (50, 75 & 95 ohm)
ing to cable. (50 & 75 ohm)
polyethylene bag. Insert the tinned conductor
into the contact. Wire must be visible through
inspection hole and dielectric pushed against
contact shoulder. For 150 ohm contact shoulder
must be flush against bushing. Heat contact
with a clean soldering iron. Avoid solder outside
contact, (50, 75, & 95 ohm)
DIELECTRIC
CRIMP RING
INSPECTION HOLE
JACKET
BRAID
50 Ohm Contact (RG-196U)
A
CRIMP RING
(assembly steps 1,
2, 3, 4, 5 & 8)
B
DIELECTRIC
SHIM
CENTER CONDUCTOR
APPLY CLEAN SOLDERING IRON
C
BUSHING
CENTER CONDUCTOR
CENTER CONTACT
BUSHING
4. Wrap shim around braid. (50 ohm)
5. Feed cable and assembled parts into coaxial
6. Thread crimp ring over cable. Feed center con-
shell. Care is required if braid is to fit smoothly
inside the shell. (50 & 75 ohm)
tact into coaxial shell with the shell between the
dielectric and the braid. (95 ohm)
JACKET
CRIMP RING
CRIMP RING
SHIM
.035 DIA
D E F
(0.89)
75 Ohm Contact (RG-187U)
(assembly steps 1,
103
2, 3, 5 & 8)
BRAID
CENTER CONTACT
150 ohm
95 ohm
75 ohm
50 ohm
BUSHING
SHELL
3/16 (4.76)
3/16 (4.76)
3/16 (4.76)
1/4 (6.35)
A
Cable Trim Dimensions
1/16 (1.59)
1/8 (3.18)
1/8 (3.18)
1/8 (3.18)
DPGM/DPJM/DPJMB
B
7. Slip crimp over the braid. (95 ohm)
8. Crimp - crimp tool must be located 1/16
(1.58) to 5 / 64 (1.98) from shoulder of coaxial.
(50, 75 & 95 ohms)
.063 (1.59) MIN. RECPT
.125 (3.18) MIN. PLUG
5/32 (3.97)
5/64 (1.98)
5/64 (1.98)
5/64 (1.98)
SEALING GROMMET LOACATION
C
95 Ohm Contact (RG-195U)
(assembly steps 1,
.154 (3.91)
.106 (2.69)
.122 (3.10)
.106 (2.69)
min. dia.
3, 6, 7 & 8)
CRIMP RING
D
Cable Entry Dimensions
.183 (4.65)
.139 (3.53)
.158 (4.01)
.136 (3.53)
max. dia.
.063 (1.59)
.078 (1.98)
E
.202 (5.13)
.153 (3.89)
EDGE OF
CRIMP TOOL
min. dia.
F
Related parts for 025-0767-001
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
025/040 III 135POS CAP ASSY H
Manufacturer:
TE Connectivity
Datasheet:
Part Number:
Description:
025 LOW PROFILE 24POS CAP ASSY
Manufacturer:
TE Connectivity
Datasheet:
Part Number:
Description:
ANALOG PANEL METER MODEL TV3 RANGE 0-500MAAC SCALE DUAL 0-700/350AAC
Manufacturer:
NEWARK SERVICES
Part Number:
Description:
025 LP HDF STRAIN RELIEF
Manufacturer:
TE Connectivity
Datasheet:
Part Number:
Description:
EMI SHIELDED ENDBELL WITH 4-40 EXTENDED JACKSCREW
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
UNIVERSAL CONTACT 1.8MM SMD
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
UNIVERSAL CONTACT 2.5MM SMD
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
UNIVERSAL CONTACT 3.5MM SMD
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
PLUG STR CRIMP SMB RG174/U 316/U
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
TRI TNM RECP M FLG SEAL 0-12
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
CONN RCPT 6POS JAM NUT W/SCKT
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
TRI R E/B STR C/C SEAL SZ 18
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
CAB CON 16S PIN 18/16 F80 SILVER
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
TRI CON SKT 16-18 TIN ST/LO
Manufacturer:
ITT Cannon
Datasheet: