MT5600BA-V92-NPS Multi-Tech Systems, MT5600BA-V92-NPS Datasheet - Page 46
![no-image](/images/no-image-200.jpg)
MT5600BA-V92-NPS
Manufacturer Part Number
MT5600BA-V92-NPS
Description
MODEM V.92 DATA/FAX WORLD
Manufacturer
Multi-Tech Systems
Series
MultiModem® IIr
Datasheets
1.SF100-G.pdf
(4 pages)
2.MT5656ZDX-EU.pdf
(55 pages)
3.MT5600BA-V92-NPS.pdf
(2 pages)
4.MT5600BA-V92-NPS.pdf
(8 pages)
5.MT5600BA-V92-NPS.pdf
(58 pages)
Specifications of MT5600BA-V92-NPS
Data Format
V.92
Interface
RS-232
Voltage - Supply
9 V ~ 12 V
Mounting Type
Desktop
Package / Case
9.0" L x 6.2" W x 1.4" H (229mm x 158mm x 36mm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
881-1060
New Zealand Telecom Warning Notice
South African Notice
This modem must be used in conjunction with an approved surge protection device.
Multi-Tech Systems, Inc. MT5600BA-V92 User Guide
1. The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has
2. Immediately disconnect this equipment should it become physically damaged, and arrange for its
3. This modem shall not be used in any manner which could constitute a nuisance to other Telecom
4. This device is equipped with pulse dialing, while the Telecom standard is DTMF tone dialing.
5. Warning Notice: No ‘111’ or other calls can be made from this device during a mains power
6. This equipment may not provide for the effective hand-over of a call to another device connected
7. Some parameters required for compliance with Telecom’s Telepermit requirements are
8. For correct operation, total of the RNs of all devices connected to a single line at any time should
accepted that the item complies with minimum conditions for connection to its network. It
indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty.
Above all, it provides no assurance that any item will work correctly in all respects with another
item of Telepermitted equipment of a different make or model, nor does it imply that any product
is compatible with all of Telecom’s network services.
This equipment is not capable under all operating conditions of correct operation at the higher
speed which it is designated. 33.6 kbps and 56 kbps connections are likely to be restricted to
lower bit rates when connected to some PSTN implementations. Telecom will accept no
responsibility should difficulties arise in such circumstances.
disposal or repair.
customers.
There is no guarantee that Telecom lines will always continue to support pulse dialing.
Use of pulse dialing, when this equipment is connected to the same line as other equipment, may
give rise to ‘bell tinkle’ or noise and may also cause a false answer condition. Should such
problems occur, the user should not contact the Telecom Faults Service.
The preferred method of dialing is to use DTMF tones, as this is faster than pulse (decadic)
dialing and is readily available on almost all New Zealand telephone exchanges.
failure.
to the same line.
dependent on the equipment (PC) associated with this device. The associated equipment shall be
set to operate within the following limits for compliance with Telecom’s Specifications:
For repeat calls to the same number:
For automatic calls to different numbers:
not exceed 5.
For automatically answered incoming calls:
•
•
•
•
There shall be no more than 10 call attempts to the same number within any 30-minute
period for any single manual call initiation, and
The equipment shall go on-hook for a period of not less than 30 seconds between the
end of one attempt and the beginning of the next attempt.
The equipment shall be set to ensure that automatic calls to different numbers are
spaced such that there is no less than 5 seconds between the end of one call attempt
and the beginning of another.
The equipment shall be set to ensure that calls are answered between 3 and 30 seconds
of receipt of ringing.
Appendix A – Regulatory Compliance
46