SP7656EN2-L Exar Corporation, SP7656EN2-L Datasheet - Page 3

IC CONV BUCK NON-SYNC 8HNSOIC

SP7656EN2-L

Manufacturer Part Number
SP7656EN2-L
Description
IC CONV BUCK NON-SYNC 8HNSOIC
Manufacturer
Exar Corporation
Series
Power Blox™r
Type
Step-Down (Buck)r
Datasheet

Specifications of SP7656EN2-L

Package / Case
8-SOIC (0.154", 3.90mm Width) Exposed Pad
Internal Switch(s)
Yes
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
0.6 V ~ 28 V
Current - Output
3A
Frequency - Switching
600kHz
Voltage - Input
4.5 V ~ 29 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
*
Output Current
3 Amps
Input Voltage
4.5 V
Operating Temperature Range
- 40 C to + 125 C
Mounting Style
SMD/SMT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
SP7656EN2-L
Manufacturer:
SIPEX
Quantity:
5 514
Part Number:
SP7656EN2-L-TR
Manufacturer:
EXAR/艾科嘉
Quantity:
20 000
Part Number:
SP7656EN2-L/TR
Manufacturer:
SIMTEK
Quantity:
301
Part Number:
SP7656EN2-L/TR
Manufacturer:
Exar
Quantity:
135
Part Number:
SP7656EN2-L/TR
Manufacturer:
SIPEX
Quantity:
20 000
Part Number:
SP7656EN2-L/TR
0
Company:
Part Number:
SP7656EN2-L/TR
Quantity:
1 996
FB
1V
PIN DESCRIPTION
PIN #
11/07/08 SP7656 PowerBlox
4,5
7,9
FAULT
1
2
3
6
8
+
-
5V
FAULT
PIN NAME
PVIN
SVIN
GND
ISET
VDR
FB
LX
VREF
Regulator feedback input. Connect to a resistive voltage-divider network to set the
output voltage. This pin can be also used for ON/OFF control. If this pin is pulled above
1V the controller resets internal soft start circuit.
Ground pin.
Power supply for the internal driver. This voltage is internally regulated to about 5V
below VIN. Place a 0.1uF decoupling capacitor between VDR and Vin as close as
possible to the IC.
Internal P-Channel FET Source. Connect to input voltage.
Input power supply for the controller. Place input decoupling capacitor as close as
possible to this pin. Connect to input voltage.
Internal P-Channel FET Drain. Connect to the output inductor.
This pin is used as a current limit input for the internal current limit comparator. Connect
to LX through an optional resistor. Internal threshold is pre-set to 300mV nominal and
can be decreased by changing the external resistor based on the following formula:
V
TRSHLD
Error Amplifier
= 300mV – 30uA * R. Where R≤3kΩ
200ms delay
+
-
VIN
I = k x VIN
UVLO
Oscillator
Set Dominant
PWM Comparator
FAULT
Register
S
R
R
3
+
-
POR
DESCRIPTION
4-Bit counter
FAULT
CONVERTER BLOCK DIAGRAM
PWM Latch
Reset Dominant
S
R
R
ENBL
SVIN
Overcurrent
Comparator
Vin - 5V LDO
5V Internal LDO
-
+
Copyright 2008 EXAR Corporation
VIN - 0.3V
VDR
FET GATE
Internal
P-FET
30uA
Power PAD
GND
VDR
PVIN
ISET
LX

Related parts for SP7656EN2-L