1035-85ML MG Chemicals, 1035-85ML Datasheet - Page 2

• Manufacturer Part Number: 1035-85ML
• Description: ADHESIVE SEAL CLEAR NONCORROSIVE
• Manufacturer: MG Chemicals
• Series: RTVr
• Type: Potting Compound, 1 Partr

Specifications of 1035-85ML

• Features: Marine Application
• Product: Silicones
• Application: Excellent for the sealing and bonding of electronic components onto printed circuit boards and protecting copper connections on electronic parts assemblies
• Chemical Component: Dimethyl Polysiloxane/Methoxy/St Polydimethylsiloxane/Tetramer Treated Silica
• Color: Translucent
• Dielectric Strength: 16.8 KV⁄mm
• Dispensing Method: Tube
• Elongation: 435%
• Hardness: 24 (Shore A)
• Primary Type: Adhesive
• Special Features: High Strength, Non-Corrosive
• Specific Gravity: 1.04
• Temperature Range: -60 to +205 °C
• Temperature, Rating: -60 to +204 °C
• Tensile Strength: 1.86 Mpa
• Thermal Conductivity: 0.06 W⁄m.°K
• Time, Cure: 12 Hr
• Time, Setting: 15 min.
• Viscosity: 360 g⁄Minute
• Weight: 3 Oz.
• Main Industry: Electronics
• For Use With/related Products: Non Corrosive
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Section 6: Accidental Release Measures
Spill
Procedure:
Section 7: Handling and Storage
Handling: Remove contact lenses before using. Do not handle contact lenses again until all sealant has been cleaned
Storage:
Section 8: Exposure Controls
Routes of
entry:
Ventilation:
Personal
Protection:
Section 9: Physical and Chemical Properties
Physical
State:
Boiling Point:
Section 10: Stability and Reactivity
Stability:
Conditions to
avoid:
Incompatibilities:
Polymerization:
Decomposition:
Section 11: Toxicological Information
Sensitization: (effects of
repeated exposure)
Carcinogenicity: (risk of
cancer)
Teratogenicity: (risk of
malformation in an unborn
fetus)
Reproductive Toxicity: (risk
of sterility)
from fingertips, nails, and cuticles. Residue may remain on fingers for several days and transfer to lenses
and cause severe eye irritation. Wash thoroughly after handling. Avoid contact with eyes, skin, and
clothing. Do not ingest or inhale. Do not expose container to heat or flame.
Keep away from sources of ignition. Store in a cool, dry, well ventilated area, away from incompatible
substances.
Remove all sources of ignition. Provide adequate ventilation. Wear appropriate personal protection.
Sprinkle absorbent compound onto spill, then sweep into a plastic or metal container. Wipe up further
residue with paper towel and place in container. Wash spill area with soap and water.
Paste
n/e
Eyes, ingestion, inhalation, and skin.
Use adequate general or local exhaust ventilation to keep airborne concentrations below exposure
limits.
Wear appropriate protective eyeglasses or chemical safety goggles. Wear appropriate protective
clothing to prevent skin contact. Use a NIOSH approved respirator when necessary.
Stable at normal temperatures and pressures.
None known
None known
Will not occur.
Carbon dioxide, and carbon monoxide, silicone dioxide, methanol, formaldehyde, nitrogen
oxide, ammonia, tin fumes.
No
The ingredients of this product are not classified as being carcinogenic by ACGIH
(American Conference of Governmental industrial Hygienists) or IARC (International
Agency for Research on Cancer), not regulated as carcinogens by OSHA (Occupational
Safety and Health Administration), and not listed as carcinogens by NTP (National
Toxicology Program)
No
No
Gravity:
Specific
Odor: alcohol
1.04
PAGE 2 / 4
Solubility: insoluble
Pressure:
Vapor
n/a
Registered Quality System ISO 9001
Vapor Density: n/a
Evaporation
Rate:
Toronto, Ontario, Canada
QMI Certificate #004008
MSDS Code:1035
< 1 (ether = 1)
pH: n/a