ABC1122P61 Panasonic Electric Works, ABC1122P61 Datasheet - Page 3

• Manufacturer Part Number: ABC1122P61
• Description: SWITCH DETECT SPST LEFT ANG SMD
• Manufacturer: Panasonic Electric Works
• Series: ABCr

Specifications of ABC1122P61

• Circuit: SPST-NO
• Switch Function: Off-Mom
• Contact Rating @ Voltage: 0.01A @ 5VDC
• Actuator Type: Angled Toggle (Detector)
• Mounting Type: Surface Mount
• Termination Style: Gull Wing
• Operating Force: 30gf
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

2. Low profile type
Right angle
NOTES
1. Mounting
1) The positioning of the switch should be
such that the pushbutton for the switch
should not directly apply force to the
operating section in the free condition.
2) During both mounting and operation,
care must be taken to protect the
pushbutton from excessive stress, as this
may cause malfunctioning. During
mounting, the insulation distance
between ground and each terminals/
cover should be confirmed as sufficient.
2. Soldering
1) For manual soldering, iron tip
temperature max. is 320°C
soldering should be completed within 3
seconds.
2) For reflow soldering, perform soldering
reflow at a peak surface temperature of
the PC board not to exceed 245°C 473°F.
3) For cream soldering, screen thickness
is recommended between 0.15 to 0.20
mm
4) During soldering, care should be taken
not to apply excessive stress to the
terminals as the resulting deformation
may cause malfunction.
5) Excessively high solder tab
temperature and soldering iron wattage
should also be avoided as these factors
may harm switching performance.
6) As this switch is thin, using flux should
be avoided for the reason of the flux may
come inside of the switch and cause
damage.
.006 to .008
.185
4.7
0.25
.010
R4.3
R.169
.024
0.6
Dystrybutor w Polsce:
AUTOMATECH Sp.z o.o.
.024
inch.
0.6
Vertical
.217
5.5
.114
.138
2.9
3.5
+0.08
−0.1
+.003
−.004
0.6
.024
0.75
.030
608°F
Horizontal
Operating angle
1.1
.043
and
.004
0.1
.024
0.6
.071
.067
1.8
1.7
.169
4.3
Tel.: [phone]
www.automatech.pl
.189
4.8
3. Switch operations
1) The installation position of the
activating unit which operates the switch
should be set at a distance of 2.8 to 3.9
mm
the positioning projection in the case of
the standard type and at a distance of 5.0
to 6.1 mm
bottom of the switch in the case of the
low-profile type.
2) Avoid using the switch as a stopper
since it may cause trouble with the
operations.
3) When using the switch to operate in
the sideways direction, ensure that the
corner roundness of the operating unit is
more than R1.
4. Environment
1) These switches do not have a sealed
construction. As such, the construction of
the equipment in which the switches are
to be installed should be given careful
consideration when the switches are to
be used in locations where corrosive
gases, silicon or other substances which
will adversely affect the contacts are
used, where there is a high concentration
of dust or where the switches may be
exposed to condensation or water. Using
switches in locations like these may
cause malfunctioning.
2) Avoid using this switch in high-
temperature, high-humidity or
condensation-forming environments and
avoid allowing droplets of water to remain
on the switch or come into contact with it.
.055
.020
1.4
0.5
.110 to .154 inch
.047
.047
1.2
1.2
.197 to .240 inch
SPST-NO (1 Form A)
.047
1.2
Circuit construction
PC board pattern
from the center of
e-mail: [e-mail]
Fax: [phone]
.169
4.3
+0
−0.15
+0
−.006
.220
from the
5.6
.335
8.5
+0.2
+.008
0
0
2-C 0.2
.008
Max. R0.5
These conditions may interfere with the
performance of the switch (resulting in
short-circuiting, migration, etc.). Use the
type with the gold contacts in applications
involving trains, aircraft, motor vehicles or
medical equipment where the switch
must satisfy safety and high reliability
requirements.
3) Because the humidity range differs
depending on the ambient temperature,
the humidity range indicated below
should be used. Continuous operation of
the switch is possible within this range,
but continuous use near the limit of the
range should be avoided.
• This humidity range does not guarantee
permanent performance.
5. Quality check under actual loading
conditions
To improve reliability, check the switch
under actual loading conditions.
6. Others
Consult with us if this switch is to be used
outside its ratings.
.020
1.8
.071
1.7
.067
(Avoid freezing when
used at temperatures
lower than 0°C 32°F)
Left angle
Operating angle
–25
–13
Tolerance range
85
5
+32
0
(Avoid
condensation
when used at
temperatures
higher than 0°C 32°F)
Humidity, %R.H.
Temperature, °C
TTP=4.8
.189
ABC1
°F
OP=6.6
176
.260
±.008
80
mm
±0.2
FP=7.1
.280
±.012
±0.3
inch
139
±.008
±0.2