SHL-Q2155 Omron, SHL-Q2155 Datasheet
SHL-Q2155
Specifications of SHL-Q2155
Related parts for SHL-Q2155
SHL-Q2155 Summary of contents
Page 1
... Panel mount roller plunger Panel mount crossroller plunger Short hinge lever SHL 128 Enclosed Switch 2. Rated Current None: Standard 01: Micro Load Note: Refer to page 135 for Molded Terminal Models. Standard model SHL-D55 SHL-Q55 SHL-Q2255 SHL-Q2155 SHL-W55 Micro voltage SHL-D55-01 SHL-Q55-01 SHL-Q2255-01 SHL-Q2155-01 SHL-W55-01 ...
Page 2
... AC-15 2 A/125 V DC-12 2 A/48 V AC-14 0.1 A/125 V DC-12 0.1 A/48 V AC-15 2 A/125 V AC-14 0.1 A/125 V DC-12 0.1 A/12 V DC-12 2 A/24 V DC-12 0.1 A/24 V DC-12 2 A/24 V DC-12 0.1 A/24 V Micro voltage SHL-W155-01 SHL-W255-01 SHL-W2155-01 SHL-W355-01 SHL-W3155-01 Volt-amperes Make Break 7,200 VA 720 VA I the ...
Page 3
... Note: 1. The above figures are for steady-state currents. 2. The above ratings may vary depending on the model. Contact your OMRON representative for further details. 3. The head section of the plunger type SHL-D(Q)@@ is excluded. 4. Durability values are calculated at an operating temperature and an operating humidity of 40% to 70%. Contact your OMRON sales representative for more detailed information on other operating environments ...
Page 4
... Rubber cap (NBR) Terminal protection cover Screw terminal Engineering Data Electrical Durability Ambient temperature Ambient humidity: 40% to 50% Operating frequency: 30 operations/min. (cosφ 250 VAC Switching current (A) 2 (NC) 4 (NO) Die-cast case (zinc die-cast) Seal rubber (NBR) Seal packing (NBR) SHL 131 Enclosed Switch ...
Page 5
... Panel Mount Roller Plunger 11 dia. × 4.7 (see note) SHL-Q2255, SHL-Q2255-01 16.9 Note: Stainless sintered alloy roller Panel Mount Crossroller Plunger 11 dia. × 4.7 (see note) SHL-Q2155, SHL-Q2155-01 16.9 Note: Stainless sintered alloy roller SHL 132 Enclosed Switch Two, 4.2 dia. ...
Page 6
... Short Hinge Lever SHL-W55, SHL-W55- 16.9 3.5 Note: Stainless steel lever Hinge Lever SHL-W155, SHL-W155- 16.9 3.5 Note: Stainless steel lever Short Hinge Roller Lever SHL-W255, SHL-W255- 16.9 3.5 Note: Sintered stainless roller Hinge Roller Lever SHL-W2155, SHL-W2155- 16.9 3.5 Note: Sintered stainless roller ...
Page 7
... One-way Action Short Hinge Roller Lever SHL-W355, SHL-W355-01 Operating direction 35.5R 6 16.9 3.5 Note: Stainless sintered roller One-way Action Hinge Roller Lever SHL-W3155, SHL-W3155-01 Operating direction 21 24 16.9 3.5 Note: Stainless sintered roller SHL 134 Enclosed Switch 9.5 dia. × 4.8 (see note) 90° ...
Page 8
... Use of the molded terminal model is recommended in locations subject to excessive dust, oil drips, or moisture. All types of SHL Switches can be fabricated into a molded terminal version. In this case, the molded terminal model will have the same dimensions and operating characteristics as the basic model from which the molded terminal model is fabricated. ...
Page 9
... When mounting the panel mount-type Switch with screws on a side surface, remove the hexagonal nuts from the actuator. Mounting Holes Two, 4.3-dia screw holes When mounting the panel mount type (SHL-Q55, SHL-Q2255, or SHL-Q2155 panel, tighten the hexagonal nuts of the actuator to a torque less than 7.84 N·m. Load Internal resistance 4.3 k ...
Page 10
... Limit Switch with ordinary contact specifications is used. Therefore, when using Limit Switches in the micro-load range, use ones with contact specifica- tions that are suited to each zone. Use the SHL-@-01 micro-load models within the zones (1 through 3) shown in the following diagram 800 mW ...
Page 11
... Cancellation; Etc. Orders are not subject to rescheduling or cancellation unless Buyer indemnifies Omron against all related costs or expenses. 10. Force Majeure. Omron shall not be liable for any delay or failure in delivery resulting from causes beyond its control, including earthquakes, fires, floods, strikes or other labor disputes, shortage of labor or materials, accidents to machinery, acts of sabotage, riots, delay in or lack of transportation or the requirements of any government authority ...
Page 12
... Complete “Terms and Conditions of Sale” for product purchase and use are on Omron’s website at www.omron247.com – under the “About Us” tab, in the Legal Matters section. ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. ...