D2F-FL Omron, D2F-FL Datasheet
D2F-FL
Specifications of D2F-FL
SW153
Available stocks
Related parts for D2F-FL
D2F-FL Summary of contents
Page 1
... D2F-01-A 30VDC plunger 0.1A @ Pin D2F-01- A1 30VDC plunger 0.1A @ Pin D2F-01-D 30VDC plunger 0.1A @ Pin D2F-01-T 30VDC plunger 0.1A @ Pin D2F-01F 30VDC plunger D2F-01F- 0.1A @ Pin 30VDC plunger A 0.1A @ Pin D2F-01F- A1 30VDC plunger Contact Operating Seal type Termination form Force SPDT ...
Page 2
... VDC 3A @ Hinge D2F-L- A1 125VAC/2A lever @ 30 VDC 3A @ Hinge D2F-L-D 125VAC/2A lever @ 30 VDC 3A @ Hinge D2F-L-T 125VAC/2A lever @ 30 VDC D2F-FL2 1A @ Roller 125VAC / lever 0.5A @ 30VDC SPDT 150g Flux Through- protection Hole PCB - Straight, supporting SPDT 150g Flux Through- protection Hole PCB - Straight ...
Page 3
... D2F-A1 D2F-01FL-D D2F-01FL-A D2F-01FL-A1 D2F-01L-D D2F-01L-A D2F-01L-A1 D2F-FL-D D2F-FL-A D2F-FL-A1 D2F-L-D D2F-L-A D2F-L-A1 D2F-01FL3-D D2F-01FL3-A D2F-01FL3-A1 D2F-01L3-D D2F-01L3-A D2F-01L3-A1 D2F-FL3-D D2F-FL3-A D2F-FL3-A1 D2F-L3-D D2F-L3-A D2F-L3-A1 D2F-01FL2-D D2F-01FL2-A D2F-01FL2-A1 D2F-01L2-D D2F-01L2-A D2F-01L2-A1 D2F-FL2-D D2F-FL2-A D2F-FL2-A1 D2F-L2-D D2F-L2-A D2F-L2-A1 D2F Snap Action Switch 1 ...
Page 4
... MD max. 0.12 mm (0.005 in) 0.12 mm (0.005 in) OP 5.5 ± 0.3 mm 5.5 ± 0.3 mm (0.22 ± 0.012 in) (0.22 ± 0.012 in) FP max. — — Characteristics Part number D2F-01L3-@, D2F-L3-@ D2F-01FL2-@, D2F-FL2-@ OF max min max. — OT min. 0.5 mm (0.020 in) MD max. 0.45 mm (0.177 in) OP 8.5 ± ...
Page 5
... Contact Form ■ Approvals UL (File No. E41515), CSA (File No. LR21642), EN conforms 61058-1 Type Rating D2F Series, D2F-01 Series 3 A, 125 VAC 1 A, 125 VAC VDC 0 VDC 0 VDC Note: The rated values approved by each of the safety standards (e.g.UL,CSA) may be different from the performance characteristics individually defined in this catalog ...
Page 6
... Roller Lever D2F-01L2-@ D2F-01FL2-@ D2F-L2-@ D2F-FL2-@ Note: 1. Unless otherwise specified, a tolerance of ± 0.4 mm applies to all dimensions. 2. Omitted dimensions are the same as pin plunger type. 3. Letters and numbers which identify the terminal are put in the blank box of the part number. 4. The above illustrations and dimensions are for models with PCB terminals. Refer to “Terminals” for models with self-supporting, solder and right/left angle terminals ...
Page 7
... Terminals D2F type PCB terminal D2F-D type Soldered terminal D2F-A type Right-angle terminal D2F-T type Self-supporting terminal D2F-A1 type Left-angle terminal Snap Action Switch D2F 5 ...
Page 8
... Precautions ■ Mounting Mount the D2F switch onto the PC board as shown in the following diagram, using 2-pitch (2 x 2.54 mm) terminal spacing. ■ PC Board Machining ■ Dimensions The use of molded components is recommended for mounting pur- poses. ■ Molded Pin Mounting Diagram When screw mounting, use M2 screws together with washers. Fas- ten the screws applying 0 ...