MRK403-A NKK Switches, MRK403-A Datasheet

MRK403-A

Manufacturer Part Number

MRK403-A

Description

SW ROTARY 4P 2-3POS BLK KNOB PC

Manufacturer

NKK Switches

Series

MRr

Type

Half-Inch Process Sealed Rotariesr

Datasheets

1.AT433A.pdf (6 pages)

2.MRA206-A.pdf (6 pages)

Specifications of MRK403-A

Number Of Positions

2 ~ 3

Number Of Decks

Number Of Poles Per Deck

Circuit Per Deck

4P3T

Contact Rating @ Voltage

0.4VA @ 28VAC/DC

Actuator Type

Knob

Mounting Type

Panel, PCB Through Hole

Termination Style

PC Pin

Orientation

Vertical

Angle Of Throw

30°

Index Angle

30 deg

Contact Style

Non Shorting

Contact Form

Contact Material

Phosphor Bronze

Contact Plating

Gold

Dielectric Strength

500 VoltsAC

Voltage Rating

28 VoltsAC/DC

Current Rating

0.4 Volt-Amp

Actuator

Shaft Actuated, with Knob

Contact Rating

0.4 Volt-Amp at 28 VoltsAC/DC

Current Rating (max)

0.4 Volt-Amp

Power Capacity (va)

0.4 Volt-Amp

Voltage Rating Ac

28 Volts

Voltage Rating Dc

28 Volts

Body Style

Miniature

Current, Rating

0.1 A

Mounting Hole Size

0.244 "

Number Of Poles

Termination

Solder

Voltage, Rating

28 VAC/VDC

Total # Of Positions

Pole Throw Configuration

Actuator Style

Shaft

Actuator Material

Brass

Illumination Type

Not Required

Ac Voltage Rating (max)

28VVAC

Dc Voltage Rating (max)

28VVDC

Mechanical Life

30000

Housing Material

Glass Fiber/Polyamide/Zinc Alloy

Product Height (mm)

25.6mm

Product Depth (mm)

12.6mm

Product Length (mm)

12.6mm

Operating Temp Range

-10C to 70C

Mounting Style

Panel

Terminal Type

PC Pins

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

Other names

360-2374
MRK403-A-RO
MRK403-A-RO

Current page: 1 of 6
Download datasheet (2Mb)

General

Series MR

Electrical Capacity (Resistive Load)

Other Ratings

Materials & Finishes

Environmental Data

Installation

Processing

Standards & Certifications

G16

Common Contacts & Terminals:

Operating Temperature Range:

Soldering Time & Temperature:

Range of Operating Torque:

End Contacts & Terminals:

Cap Installation Force:

Insulation Resistance:

Contact Resistance:

Dielectric Strength:

Movable Contacts:

Bushing/Housing:

Mounting Torque:

For MRF or MRK:

Mechanical Life:

Contact Timing:

Stopper Plate:

Electrical Life:

Vibration:

Humidity:

Cleaning:

For MRA:

Indexing:

Sealing:

Shock:

Shaft:

Base:

Specifications

250mA @ 125V AC

0.4VA maximum @ 28V AC/DC maximum

(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)

Note: Find additional explanation of operating range in Supplement section.

10 milliohms maximum for MRA; 50 milliohms maximum for MRF & MRK

100 megohms minimum @ 500V DC

1,000V AC minimum for 1 minute minimum for MRA

500V AC minimum for 1 minute minimum for MRF & MRK

30,000 operations minimum

10,000 operations minimum

0.02 ~ 0.07Nm for MRA; 0.005 ~ 0.02Nm for MRF & MRK

Nonshorting (break-before-make)

MRA – self-cleaning, sliding contact; MRF & MRK – self-cleaning, rotary contactor disk

30°

Brass with nickel plating

Steel with zinc plating for MRA & MRK; polyamide cover with stopper for MRF

Zinc alloy with zinc plating

Copper with silver plating for MRA; phosphor bronze with gold plating for MRF & MRK

Brass with silver plating for MRA; phosphor bronze with gold plating for MRF & MRK

Diallyl phthalate for MRA; fiberglass reinforced polyamide for MRF & MRK

–10°C through +70°C (+14°F through +158°F)

90 ~ 95% humidity for 96 hours @ 40°C (104°F)

10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning

in 1 minute; 3 right angled directions for 2 hours

50G (490m/s

MRK model meets IP67 of IEC60529 standards

.686Nm (6.08 lb

19.6 ~ 29.4N (4.41 ~ 6.61 lbf) for MRA & MRK

Wave Soldering for MRA: See Profile A in Supplement section.

Wave Soldering for MRF & MRK: See Profile B in Supplement section.

Manual Soldering for MRA: See Profile A in Supplement section.

Manual Soldering for MRF & MRK: See Profile B in Supplement section.

Automated cleaning recommended. Stopper plate, as well as washers for MRA & MRK, must be in

place to maintain automated cleaning. See Cleaning specifications in Supplement section.

MRA, MRF, & MRK models have not been tested for UL recognition or CSA certification.

These switches are designed for use in a low-voltage, low-current, logic-level circuit.

When used as intended in a logic-level circuit, the results do not produce hazardous energy.

) acceleration (tested in 3 right angled directions, with 3 shocks in each direction)

www.nkk.com

•

in)

Half-Inch Diameter Process Sealed Rotaries

Related parts for MRK403-A

MRK403-A Summary of contents

Page 1

... Range of Operating Torque: 0.02 ~ 0.07Nm for MRA; 0.005 ~ 0.02Nm for MRF & MRK Contact Timing: Nonshorting (break-before-make) MRA – self-cleaning, sliding contact; MRF & MRK – self-cleaning, rotary contactor disk Indexing: 30° Materials & Finishes Shaft: Brass with nickel plating Stopper Plate: Steel with zinc plating for MRA & ...

Page 2

... Adjustable stopper plate allows 2–12 position settings. High contact reliability achieved by the self-cleaning contact mechanism. Break-before-make contact timing with sliding contacts in MRA and rotary contactor disk in MRF and MRK models. Interior housing seal and molded-in PC terminals, plus shaft rubber o-ring on MRA and MRK and polyamide cover on MRF model, allow cleaning after automated soldering. MRK model meets IP67 of IEC60529 specifications (similar to NEMA 4 & ...

Page 3

Series Actuators & Terminals A Shaft Actuated with PC Terminals Low Profile Screwdriver Actuated F with PC Terminals Low Profile Shaft Actuated with K PC Terminals DESCRIPTION FOR TYPICAL ORDERING EXAMPLE G Shaft Actuated A with PC ...

Page 4

... MRF403 2–3 MRK403 2–3 POSITION SETTING FOR MRA, MRF, & MRK MODELS Each switch is supplied with the stopper set for the maximum number of positions allowed for that model. Prior to installation, the desired position setting should be made. Contact factory for continuous rotation. ...

Page 5

... Dia (9.5) Dia .374 .374 2 Pole (12.6) Dia (12.6) Dia .496 .496 1 Pole 2 Pole B (12.6) Dia (12.6) Dia (12.6) Dia .496 .496 .496 Double Pole Four Pole MRF206 MRF403 MRK206 MRK403 (0.8) Dia Typ .031 (12.0) Dia (12.0) Dia .472 C .472 ...

Page 6

Half-Inch Diameter Process Sealed Rotaries AT433 A Plain Black Material: Base Material: Polyacetal Polyester Base Color: (19.0) Dia .748 Color: Black (11.0) Dia .433 Black only Polyamide Tip (13.0) Colors: .512 (9.5) .374 ...

Related keywords

MRK403-A datasheet
MRK403-A data sheet
MRK403-A pdf datasheet
MRK403-A component
MRK403-A part
MRK403-A distributor
MRK403-A RoHS
MRK403-A datasheet download