A30403RNZQ C&K Components, A30403RNZQ Datasheet - Page 5

• Manufacturer Part Number: A30403RNZQ
• Description: SWITCH ROTARY 3P 4POS 2.5A SLD
• Manufacturer: C&K Components
• Series: Ar

Specifications of A30403RNZQ

• Number Of Positions: 4
• Number Of Decks: 1
• Number Of Poles Per Deck: 3
• Circuit Per Deck: 3P4T
• Contact Rating @ Voltage: 2.5A @ 125VAC
• Actuator Type: Flatted (6.35mm dia)
• Mounting Type: Panel Mount
• Termination Style: Solder Lug
• Orientation: Vertical
• Angle Of Throw: 30°
• Total # Of Positions: 4
• Pole Throw Configuration: 3P
• Actuator Style: Shaft
• Actuator Material: Glass/Nylon 6/6
• Current Rating (max): 2.5A
• Illumination Type: Not Required
• Ac Voltage Rating (max): 125VVAC
• Dc Voltage Rating (max): 125VVDC
• Contact Material: Coin Silver
• Contact Plating: Silver
• Product Height (mm): 38.37mm
• Product Depth (mm): 26.19mm
• Product Length (mm): 26.19mm
• Operating Temp Range: -30C to 85C
• Mounting Style: Panel
• Terminal Type: Solder Lug
• Contact Form: 3P
• Dielectric Strength: 1000 Volts
• Voltage Rating: 125 Volts
• Current Rating: 2.5 Amps, 350 mAmps at 125 Volts
• Actuator: Rotary
• Contact Rating: 2.5 Amps, 350 mAmps at 125 Volts
• Voltage Rating Ac: 125 Volts
• Voltage Rating Dc: 125 Volts
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: *A30403RNZQ; A30403RNZQ; CKN6043

Setting Stops on A112 and A125 Models
The number of switch positions is adjustable on A112
and A125 models only by means of a stop ring provided
with each switch. The number of positions is pre-set on
all other models and the stop ring is factory installed.
Soldering, Cleaning and Assembly Instructions for ‘MC’ Termination Option
Soldering
1. Insert switch base only into PC board.
2. Do not bend terminals.
3. Wave soldering recommended at
4. Hand solder at 500F, 10 sec.
Switch Assembly
1. Hold housing/shaft assembly by housing. Remove
2. Do not push on switch shaft. Detent mechanism will
3. While holding switch housing, align locating tab on
4. Push firmly on housing until latches snap in place.
5. Remove clip from shaft and discard. Assembly is
Stop ring
PART NO.
767B00201
Material: Brass
Finish: Nickel plated
NONE
500F solder temperature.
max./terminal.
protective cap by squeezing tabs and discard. (FIG. 1)
come apart.
base with notch on housing and engage 4 housing
latches in slots on base. (FIG. 2)
complete. (FIG. 3)
NO SEAL
E
EPOXY SEAL
FUNCTION
AVAILABLE HARDWARE
F
SPLASHPROOF BUSHING SEAL
K–7
Cleaning
1. Flux clean using vapor degreaser and forced
2. Do not allow switch base to ‘trap’ fluids.
3. Freon TMC, TF or Methylene Chloride give
To set stops: Turn shaft fully counter-clockwise and
insert stop ring tab in desired hole. Install lockwasher
and nut to retain stop ring for both PC and panel
mounting. Switch without stop ring has 12 positions.
rinse or triple bath method.
excellent results.
SPLASHPROOF
BUSHING SEAL
(FIG. 1)
1-4 Pole Rotary Switches
REMOVABLE CLIP
K
EPOXY & SPLASHPROOF BUSHING SEAL
Specifications and dimensions subject to change
(FIG. 2)
www.ck-components.com
LOCATING
Dimensions are shown: mm
STANDOFF
A Series
TAB
(FIG. 3)
K