A22L-TW-24A-10M Omron, A22L-TW-24A-10M Datasheet - Page 27
![SWITCH PB ILL RND MOM SPST-NO](/photos/14/93/149303/a22l-tw-24a-10m__a22l-tw-t1-10m_sml.jpg)
A22L-TW-24A-10M
Manufacturer Part Number
A22L-TW-24A-10M
Description
SWITCH PB ILL RND MOM SPST-NO
Manufacturer
Omron
Series
A22r
Type
Illuminatedr
Specifications of A22L-TW-24A-10M
Circuit
SPST-NO
Switch Function
Off-Mom
Contact Rating @ Voltage
10A @ 110VAC
Actuator Type
Round Button
Illumination Type, Color
LED, White
Illumination Voltage (nominal)
24 VAC/DC
Mounting Type
Panel Mount
Termination Style
Screw Terminal
Contact Form
SPST - NO
Contact Rating
10 mAmps
Actuator
Round, Projection
Mounting Style
Panel
Illumination
Illuminated
Illumination Color
White
Body Shape
Square
Dielectric Strength
2500 Volts
Insulation Resistance
100 MOhms
Mounting Angle
Straight
Operating Force
29.4 N
Water / Moisture Rating
IP65
Current Rating (max)
10 Amps
Voltage Rating Ac
440 Volts
Voltage Rating Dc
380 Volts
Ip Rating
IP65
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
A22LTW24A10M
Z1495
Z1495
Mounting the Operation Unit on the
Panel
Insert the Operation Unit (Pushbutton, etc.) from the front surface of
the panel, insert the Lock Ring and the mounting nut from the termi-
nal side, then tighten the nut. Before tightening, check that the rubber
washer is present between the Pushbutton Unit and the panel.
When using a Legend Plate Frame, put one rubber washer each
between the Legend Plate Frame and the panel and between the
Operation Unit and the Legend Plate Frame. (One rubber washer will
be provided when one Legend Plate Frame is ordered.)
Align the Lock Ring with the groove in the casing, then insert the
Lock Ring so that its edge is located on the panel side.
Tighten the mounting nut at a torque of 0.98 to 1.96 N·m.
When using a Lock Ring, replace with the supplied Lock Ring, insert
the projecting part into the lock slot, and then tighten the mounting
nut.
When the panel cutout dimension is 25 dia., remove the supplied
rubber washer and mount the 25-dia. Ring as shown below. (Since
the A22Z-R25 is not attached to the main body, order separately.)
Hold here
Lock Ring
Panel
Mounting nut
Rubber washer
Panel
Lock Ring
22.3 dia.
22.3 dia.
22 dia.
25 dia.
25 dia.
Mounting nut
25-dia. Ring
Operation Unit
(A22Z-R25)
Pro-
jecting
part
Panel
Lock Ring
Mounting the Switch on the
Pushbutton Unit
Insert the Pushbutton Unit into the Switch Unit, aligning the arrow
mark inscribed on the Case with the lever on the Switch Blocks, then
move the lever in the direction indicated by the arrow in the following
figure.
Removing the Switch
Move the lever in the direction indicated by the arrow in the following
figure, then pull the Pushbutton Unit or the Switch Blocks.
Since the lever has a hole with an inside diameter of 6.5 mm, the
lever can be moved in the specified direction by inserting a screw-
driver into the hole and then moving the screwdriver.
■ Mounting/Replacing the Color
Projection, Fall-guard
Grip and rotate the Color Cap with your fingers.
Cap
Pushbutton Switch
Operation Unit
Arrow mark
A22
Screwdriver
Lever
G-101