DRAR16H-RO NKK Switches, DRAR16H-RO Datasheet - Page 2

• Manufacturer Part Number: DRAR16H-RO
• Description: SW ROTARY DIP HEX ORN RT ANGLE
• Manufacturer: NKK Switches
• Series: DRr

Specifications of DRAR16H-RO

• Circuit: Hexadecimal
• Number Of Positions: 16
• Contact Rating @ Voltage: 0.1A @ 5VDC
• Actuator Type: Rotary with Shaft
• Actuator Level: Raised
• Mounting Type: Through Hole
• Orientation: Side Actuated
• Washable: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

General Specifications
NKK Switches • email: [e-mail] • Phone [phone] • Fax [phone]
Electrical Capacity (Resistive Load)
Other Ratings
Materials & Finishes
Environmental Data
Installation
Standards & Certifications
Soldering Time & Temperature:
Shaft & Bushing (DRA only):
Nominal Operating Torque:
Mounting Torque for DRA:
Flammability Standards:
Operating Temp Range:
Knob Installation Force:
Nonswitching Rating:
Insulation Resistance:
or CSA Certification:
Stationary Contacts:
Contact Resistance:
Dielectric Strength:
Movable Contact:
Switching Rating:
Housing & Case:
Mechanical Life:
Contact Timing:
UL Recognition
Electrical Life:
Process Seal:
Terminals:
Vibration:
Humidity:
Actuator:
O-rings:
Note: A detent operation is one actuator position operation or stepping.
Shock:
20,000 detent operations = 1,250 cycles for hexadecimal devices or
Base:
2,000 cycles for decimal devices. A cycle is one 360° rotation.
100mA @ 5V DC
100mA @ 50V DC
80 milliohms maximum for all 4 contacts closed
30 milliohms maximum for 1 contact closed
1,000 megohms minimum @ 250V DC
250V AC minimum for 1 minute minimum
20,000 detent operations minimum
20,000 detent operations minimum
80 ~ 320 grams-cm (1.1 ~ 4.4 ounce
Shorting (Avoid possible false signal by turning off power before switching.)
Brass with nickel plating
Glass fiber reinforced polyester (PBT) (UL 94V-0)
Glass fiber reinforced polyester (PBT) (UL 94V-0)
Nitrile butadiene rubber
Glass fiber reinforced polyester (PBT) (UL 94V-0)
Copper with gold plating
Phosphor bronze with gold plating
Phosphor bronze with gold plating
-25°C through +75°C (-13°F through +167°F)
90 ~ 95% for 96 hours @ 40C° (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range
& returning in 1 minute; 3 right angled directions for 2 hours
50G (490m/s
1.47Nm (13.0 lb
39.2N maximum (8.82 lbf) for DRA model; 29.4N maximum (6.61 lbf) for DRF/DRF2 models
3 seconds @ 350°C manual soldering or 5 seconds @ 270°C solder pot
See Supplement Index (page Z2) for specific processing data.
UL 94V-0 rated actuator, housing, case, & base
The DR series rotaries have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
2
10mm Washable DIP Rotaries
) acceleration (tested in 3 right angled directions, with 3 shocks in each direction)
•
in) for double nut; .686Nm (6.08 lb
•
in)
•
www.nkkswitches.com
in) for single nut
Series DR
8-03