A16-1NGN Omron, A16-1NGN Datasheet - Page 15

• Manufacturer Part Number: A16-1NGN
• Description: NEON LAMP 110V GREEN FOR A16
• Manufacturer: Omron
• Type: Neon Lamp, 110 VoltsACr
• Series: A16r

Specifications of A16-1NGN

• Accessory Type: Neon Lamp Replacement
• Supply Voltage: 110V
• Base Type: Bi-Pin
• Colour: Green
• Current Rating: 1.5mA
• Svhc: No SVHC (15-Dec-2010)
• Illumination Colour: Green
• Operating Lifetime: 10000h
• Voltage Rating Vac: 110V
• Average Bulb Lif: RoHS Compliant
• Color: Green
• Illumination: Illuminated
• Height: 13 mm
• Illumination Color: Green
• Mounting Style: Snap In
• Termination Style: Tabs
• Lamp Base Type: Bi-Pin
• Rohs Compliant: Yes
• Average Bulb Life: 10000h
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: A16 Series
• For Use With: Z1396 - SWTCH KNOB RND 3POS DPDT ILL GRNZ1393 - SWTCH KNOB RND 2POS SPDT ILL GRNZ1390 - SWTCH KNOB RND 2POS SPDT ILL GRNZ1384 - SWITCH KNB RECT 3POS DPDT ILLZ1381 - SWITCH KNB RECT 2POS SPDT ILLZ1378 - SWITCH KNB RECT 2POS SPDT ILLZ1372 - SWITCH KNOB SQ 3-POS DPDT ILLZ1369 - SWITCH KNOB SQ 2-POS SPDT ILLZ1366 - SWITCH KNOB SQ 2-POS SPDT ILLZ1308 - SWITCH PB RND MOM DPDT ILLUM GRNZ1304 - SWITCH PB RECT MOM DPDT ILLUMZ1300 - SWITCH PB SQ MOM DPDT ILLUM GRN
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: A161NGN; Z1343

A16 / M16
Installation
After mounting the Pushbutton Unit to the panel, snap in the Socket
Unit from the back of the panel.
Mounting the Panel
Insert the Pushbutton Unit into the front of the panel, and fix the lock
ring and mounting nut from the terminal side.
Make sure that the lock ring is aligned with the thread of the case
and the edge of the lock ring is touching the panel.
Tighten the mounting nuts to a torque of 0.20 to 0.39 N
5 kgf cm).
The maximum tightening torque is 0.39 N m (5 kgf cm).
Switch Mounting
Snap on the Switch Unit to the Pushbutton Unit.
Make sure the the Switch Unit is in the proper orientation when
snapping on to the Pushbutton Unit.
Switch Removal
Grip the part between the Switch holder of the case and the Switch
Unit using the A16Z-5080 Extractor, and pull to remove the Switch
Unit.
Mounting the Panel
Case
A16Z-5080 Extractor
Edge
Thread
Panel
Lock ring
Mounting nut
m (3 to
ing Part
Removing and Mounting the Operating Part
Removing the Lamp
Removing from the Operating Part End
Removing from the Switch Unit End
The Lamp can be removed by hand once the Switch is removed
using the A16Z-5080 Extractor.
Installing the Lamp
When mounting the Lamp, make sure it is facing the direction shown
in the following diagram. Insert the Lamp while matching the pro-
truding part of the Lamp and the small guides on the outer surface of
the case.
The Lamp can be mounted from the operating part end by using the
A16Z-5080 Extractor. The lamp can be mounted by following the
opposite procedure for removing the Lamp.
1. Remove the operating part as shown in the following
2. To attach the operating part, push until it clicks into place.
Mounting and Replacing the Operat-
diagram. If the operating part cannot be removed by hand,
use the A3PJ-5080 Extractor.
Protruding part
Lamp
Grip the Lamp with the
A16Z-5080 Extractor and
pull to remove.
Operating section
A16 / M16
15