A16ZA-3003 Omron, A16ZA-3003 Datasheet - Page 44

• Manufacturer Part Number: A16ZA-3003
• Description: PANEL PLUG SQUARE
• Manufacturer: Omron
• Type: Pushbuttonr
• Series: A16, M 16r

Specifications of A16ZA-3003

• Accessory Type: Panel Hole Plug
• Color: Black
• Illumination: Not Illuminated
• Length: 18 mm
• Mounting Style: Panel
• Width: 18 mm
• For Use With/related Products: A16 Series
• For Use With: Z1375 - SWITCH KNOB RECT 2-POS SPDTZ1374 - SWITCH KNOB SQ 3-POS DPDT ILLZ1373 - SWITCH KNOB SQ 3-POS DPDT ILLZ1372 - SWITCH KNOB SQ 3-POS DPDT ILLZ1371 - SWITCH KNOB SQ 2-POS SPDT ILLZ1370 - SWITCH KNOB SQ 2-POS SPDT ILLZ1369 - SWITCH KNOB SQ 2-POS SPDT ILLZ1368 - SWITCH KNOB SQ 2-POS SPDT ILLZ1367 - SWITCH KNOB SQ 2-POS SPDT ILLZ1366 - SWITCH KNOB SQ 2-POS SPDT ILLZ1365 - SWITCH KNOB SQ 3-POS DPDTZ1364 - SWITCH KNOB SQ 2-POS SPDTZ1363 - SWITCH KNOB SQ 2-POS SPDTZ1317 - SWITCH PB SQUARE MOM DPDT YELLOWZ1316 - SWITCH PB SQUARE MOM DPDT WHITEZ1315 - SWITCH PB SQUARE MOM DPDT REDZ1314 - SWITCH PB SQUARE MOM DPDT GREENZ1313 - SWITCH PB SQUARE MOM DPDT BLACKZ1312 - SWITCH PB SQUARE MOM DPDT BLUEZ1303 - SWITCH PB SQ MOM DPDT ILLUM YLLWZ1302 - SWITCH PB SQ MOM DPDT ILLUM WHTZ1301 - SWITCH PB SQ MOM DPDT ILLUM REDZ1300 - SWITCH PB SQ MOM DPDT ILLUM GRN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: A16ZA3003; A3BA-3003; Z1334

Correct Use
J NUT MOUNTING
Insert the buzzer unit from the front of the panel and tighten the
mounting nut inserted from the rear of the panel.
Since a projection exists on the rear portion of the buzzer unit, if
the mounting nut cannot be fitted into position, turn the nut
slightly.
The tightening torque of the mounting nut should be less than
5 kg-cm.
Solder the terminals after mounting the nut. Otherwise, the
terminals, when thickened by solder, may prevent the nut from
being screwed down onto the buzzer unit.
J MOUNTING
Tighten the mounting nut at a torque of less than 5 kg-cm.
J WIRING
Exercise caution that the input terminals are not short-circuited
by the short-circuiting jumper.
Finish soldering within 5 seconds with a 30 watt soldering iron, or
within 3 seconds at a solder temperature of 240°C. For about a
minute after soldering, do not apply any force to the buzzer unit,
to avoid deforming the softened plastic buzzer unit base.
Use an non-corrosive, resin-based soldering flux.
J SNAP-IN MOUNTING
Attach the mounting leaf spring to the buzzer. Engage the edges
of the leaf spring in the two grooves on the threaded section of
the buzzer. After inserting the leaf spring edges into the grooves,
confirm that the leaf spring has seated. Be sure to attach both
leaf springs.
Insert the buzzer assembly into the hole on the mounting panel
from the front.
M2BJ-B
45
J SHORT-CIRCUITING JUMPER
The buzzer sounds continuously or intermittently depending on
how the short-circuiting bracket is attached to the case guide.
When the bracket is attached with the triangle on it facing
direction A (PC board side), the buzzer sounds intermittently.
To produce continuous sounds, attach the bracket to the case
guide so that the triangle on the bracket faces direction B.
M2BJ-B