10520 Desco, 10520 Datasheet - Page 4

• Manufacturer Part Number: 10520
• Description: FINISH FLOOR STATGUARD 55GAL
• Manufacturer: Desco
• Series: Statgaurd®r

Specifications of 10520

• Cleaner, Treatment Type: AntiStatic Liquid, Finish
• Applications: Floors
• Lead Free Status / RoHS Status: Not applicable / Not applicable

TB-2088 Page 4 of 9
Equipment needed:
•
•
1. Pour Statguard
Figure 4. Applying floor finish
2. Let the first coat dry thoroughly at least 60 minutes,
3. Let second coat dry thoroughly for at least 60
4. One or preferably two additional coats of floor finish
5. Maintain the polish following the Dust Mop, Damp
Statguard
DUST MOP PROGRAM
1. Keep the floor surface clean. Use an untreated dust
Clean rayon (or cotton blend) mop, dedicated to
Statguard
Bucket dedicated to Statguard
only.
bucket and apply with a clean rayon (or cotton
blend) mop using a figure 8 motion.
then apply a second coat. Do not use force air
drying.
minutes to yield a bright gloss. Repeat application
to attain higher gloss and higher conductivity (two
coats will provide acceptable antistatic performance
on most floors). Keep traffic from floor for at least
one hour after the last coat is applied. See dry time
recommendations on page 3 in this technical
bulletin.
should be applied if the floor is to be maintained by
dry burnishing or spray buffing.
Mop, Floor Cleaner, Dry Burnish, or Spray Buff
maintenance procedure below.
mop or push broom nightly or as needed to remove
accumulated dirt and insulative contaminant.
®
®
Maintenance
Floor Finish use only
DESCO EAST - One Colgate Way, Canton, MA 02021-1407 • [phone] • Fax [phone] • Web Site: Desco.com
®
Floor Finish into a clean mop
DESCO WEST - 3651 Walnut Avenue, Chino, CA 91710 • [phone] • Fax [phone]
®
Floor Finish use
DAMP MOP PROGRAM
1. Keep the floor surface clean. Use an untreated dust
2. To damp mop, use a 1 to 3 dilution of Statguard
FLOOR CLEANER PROGRAM
Statguard
heel marks. As a cleaner it will reduce the gloss of the
floor.
Heavy-Moderate Traffic:
Clean once a week, or as dictated by floor appearance.
Low Traffic Floors:
Clean floors as dictated by floor appearance.
1. Dust mop with untreated mop.
2. Dilute Statguard
3. Damp mop floor with cleaner solution and let dry
DRY BURNISH PROGRAM
Heavy-Moderate Traffic:
A dry burnish program will increase gloss and remove
surface imperfections.
Dry burnish once a week or as dictated by floor
appearance.
Low Traffic Floors:
Dry burnish as dictated by floor appearance.
1. Dust mop with an untreated mop.
2. Dry burnish at 1000-2000 rpm.
3. After dry burnish, dry mop the area with an
SPRAY BUFF PROGRAM
A spray buff program will repair scratches, marks, and
other imperfections as well as gloss.
Heavy-Moderate Traffic:
Spray buff once a week or as dictated by appearance.
Low Traffic Floors:
Spray buff as dictated by floor appearance.
mop or push broom nightly or as needed to remove
accumulated dirt and insulative contaminant.
water (1 part Statguard
thoroughly. The mop and bucket should be
dedicated to Statguard
clean water to 1 part Floor Cleaner. For example,
use five (5) gallons of clean water to two (2) quarts
of floor cleaner.
thoroughly. The mop and bucket should be
dedicated to Statguard
untreated dry mop if necessary.
®
Floor Cleaner will clean surface stains and
®
Dissipative Floor Cleaner 10 parts
®
®
®
use only.
use only.
to 3 parts water). Let dry
© 2008 DESCO INDUSTRIES, INC.
®
Employee Owned
in