70-3-25 ITW Chemtronics, 70-3-25 Datasheet
70-3-25
Manufacturer Part Number
70-3-25
Description
DESOLDER BRAID UNFLUXED 25'
Manufacturer
ITW Chemtronics
Series
Soder-Wick® SW 70r
Type
Unfluxedr
Specifications of 70-3-25
Width
0.080" (2.03mm)
Length
25' (7.622m)
Color
Green
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
Q1142291
ITW CHEMTRONICS
SECTION 1: CHEMICAL PRODUCT AND COMPANY INFORMATION
Company Address:
8125 Cobb Center Drive
Kennesaw, GA 30152
Product Identification
Product Code: 70, 75 Series (All Part Numbers)
SECTION 2: COMPOSITION, INFORMATION ON INGREDIENTS
Product Ingredient Information
Copper
SECTION 3: HAZARD IDENTIFICATION
Emergency Overview: Shiny, braided copper wire. This product is nonflammable.
Potential Health Effects:
Eyes: Vapors released from other materials used in the desoldering process may cause eye irritation.
Skin: Prolonged contact may cause skin irritation and/or sensitization.
Ingestion: Not likely.
Inhalation: Vapors from soldering processes may cause irritation of the nose and throat. Respiratory sensitization may result from the inhalation of rosin fumes.
Pre-Existing Medical Conditions Aggravated by Exposure: None known.
SECTION 4: FIRST AID MEASURES
Eyes:
Have eyes examined and tested by medical personnel if irritation develops or persists.
Skin:
separately before reuse.
Ingestion: Get medical attention.
Inhalation: If user is overcome by fumes during the desoldering process remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give
oxygen and get immediate medical attention.
SECTION 5: FIRE FIGHTING MEASURES
Flash Point: Nonflammable
Extinguishing Media: Water fog, CO 2 , dry chemical, foam are compatible for extinguishing fires involving other materials when Soder-Wick is present.
Fire Fighting Instructions: As in any fire, wear self-contained breathing apparatus (pressure-demand, MSHA/NIOSH approved or equivalent) and full protective gear.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Small Spills: Pick up and store in a closed container for delivery to a metals recycling center. Do not dispose of by placing in trash.
SECTION 7: HANDLING AND STORAGE
Avoid prolonged or repeated contact with eyes, skin. Wash hands before eating. Use with adequate ventilation. Avoid breathing vapors given off by the desoldering
process. Store in a cool dry place. Keep container closed when not in use. KEEP OUT OF REACH OF CHILDREN.
SECTION 8: EXPOSURE CONTROLS/PERSONNEL PROTECTION
Exposure Guidelines:
CHEMICAL NAME
Copper
Work/Hygienic Practices: Ventilation is recommended to control airborne levels of desoldering process vapors. Wear safety glasses with side shields or goggles when
using this product.
NFPA and HMIS Codes:
Health
Flammability
Reactivity
Personal Protection
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Physical State: Braided copper wire
Odor: None
pH: NA
Vapor Pressure: NA
Vapor Density: MA
Color: Copper metallic
SECTION 10: STABILITY AND REACTIVITY
Stability: This product is stable.
Incompatibility: Do not mix with powdered alkali and alkaline earth metals or strong oxidizing agents.
Products of Decomposition: Carbon dioxide, carbon monoxide.
Hazardous Polymerization: Will not occur
Conditions to Avoid: NA
If eye irritation occurs immediately flush with plenty of water. After initial flushing, remove any contact lenses and continue flushing for at least 15 minutes.
If skin irritation occurs wash skin with soap and water. Remove contaminated clothing. Get medical attention if irritation develops or persist. Wash clothing
Product Information: 800-TECH-401
Customer Service:
®
800-645-5244
Conditions to Avoid: None known
SODER-WICK® UNFLUXED, SODER-WICK® UNFLUXED SD
LEL/UEL: Not applicable
ACGIH TLV
0.2 mg/m 3
Page 1 of 2
Emergency:
CAS#
7440-50-8
NFPA
1
0
1
-
Revision Date: February 17, 2010
Solubility in Water: Insoluble
Specific Gravity: (Water =1) 8.92
Evaporation Rate: NA
Viscosity: NA
Percent Volatile: NA
Boiling Point: 604 F @ 100mm Hg
(Chemtrec) 800-424-9300
OSHA PEL
1.0 mg/m 3
Wt. % Range
100.0%
HMIS
1
0
1
-
ACGIH STEL
NA
MSDS #1401
70-3-25 Summary of contents
Page 1
... Cobb Center Drive Kennesaw, GA 30152 Product Information: 800-TECH-401 Customer Service: 800-645-5244 Product Identification Product Code: 70, 75 Series (All Part Numbers) SECTION 2: COMPOSITION, INFORMATION ON INGREDIENTS Product Ingredient Information Copper SECTION 3: HAZARD IDENTIFICATION Emergency Overview: Shiny, braided copper wire. This product is nonflammable. ...
Page 2
... ITW CHEMTRONICS SECTION 11: TOXICOLOGICAL INFORMATION Inhalation: Inhalation of dust and fumes during desoldering can irritate the respiratory tract and cause respiratory sensitization. Ingestion: Not a typical route of exposure. Skin: Can cause skin sensitization in some individuals. Eye: Contact with rosin dust and desoldering fumes can irritate the eyes. ...