10-100L ITW Chemtronics, 10-100L Datasheet
![DESOLDER BRAID .100" BLUE](/photos/14/44/144488/10-100l_sml.jpg)
10-100L
Manufacturer Part Number
10-100L
Description
DESOLDER BRAID .100" BLUE
Manufacturer
ITW Chemtronics
Series
Chem-Wik®r
Type
Rosin, Non Activated (R)r
Specifications of 10-100L
Width
0.100" (2.54mm)
Length
100' (30.5m)
Color
Blue
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
ITW CHEMTRONICS
SECTION 1: CHEMICAL PRODUCT AND COMPANY INFORMATION
Company Address:
8125 Cobb Center Drive
Kennesaw, GA 30152
Product Identification
Product Code: All Part Numbers
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
Product Ingredient Information
Copper
Rosin
SECTION 3: HAZARD IDENTIFICATION
Emergency Overview: Shiny, braided copper wire. This product is nonflammable.
Potential Health Effects:
Eyes: Vapors released from the desoldering process may cause eye irritation.
Skin: Prolonged contact may cause skin irritation and/or sensitization.
Ingestion: Not likely.
Inhalation: Vapors from soldering processes may cause irritation of the nose and throat. Respiratory sensitization may result from inhalation of rosin fumes.
Pre-Existing Medical Conditions Aggravated by Exposure: Lung and skin.
SECTION 4: FIRST AID MEASURES
Eyes:
Have eyes examined and tested by medical personnel if irritation develops or persists.
Skin:
clothing separately before reuse.
Ingestion: Get medical attention.
Inhalation: If user is overcome by fumes during the desoldering process remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give
oxygen and get immediate medical attention.
SECTION 5: FIRE FIGHTING MEASURES
Flash Point: Nonflammable
Extinguishing Media: Water fog, CO 2 , dry chemical, foam.
Fire Fighting Instructions: As in any fire, wear self-contained breathing apparatus (pressure-demand, MSHA/NIOSH approved or equivalent) and full protective gear.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Small Spills: Pick up and store in a closed container for delivery to a metals recycling center. Do not dispose of by placing in trash.
SECTION 7: HANDLING AND STORAGE
Avoid prolonged or repeated contact with eyes and skin. Wash hands before eating. Use with adequate ventilation. Avoid breathing vapors given off by he
desoldering process. Store in a cool dry place. Keep container closed when not in use. KEEP OUT OF REACH OF CHILDREN.
SECTION 8: EXPOSURE CONTROLS/PERSONNEL PROTECTION
Exposure Guidelines:
CHEMICAL NAME
Copper
Rosin
using this product.
NFPA and HMIS Codes:
Health
Flammability
Reactivity
Personal Protection
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Physical State: Coated braided copper wire
Odor: None
pH: NA
Vapor Pressure: NA
Vapor Density: NA
Color: Copper metallic
Work/Hygienic Practices: Ventilation is recommended to control airborne levels of desoldering process vapors. Wear safety glasses with side shields or goggles when
If eye irritation occurs immediately flush with plenty of water. After initial flushing , remove any contact lenses and continue flushing for at least 15 minutes.
If skin irritation occurs wash skin with soap and water. Remove contaminated clothing. Get medical attention if irritation develops or persist. Wash
Product Information: 800-TECH-401
Customer Service:
®
800-645-5244
CHEM-WIK®ROSIN / CHEM-WIK® ROSIN SD
LEL/UEL: Not applicable
ACGIH TLV
0.2 g/m 3
NA
m
Page 1 of 2
Emergency:
CAS#
NFPA
7440-50-8
8050-09-7
1
0
1
-
Revision Date: February 17, 2010
Solubility in Water: Insoluble
Specific Gravity: (Water =1) 8.92
Evaporation Rate: NA
Viscosity: NA
Percent Volatile: NA
Boiling Point: 604F @ 100mm Hg
(Chemtrec) 800-424-9300
OSHA PEL
1.0 g/m 3
NA
m
Wt. % Range
90.0-98.0
HMIS
2.0-10.0
1
0
1
-
ACGIH STEL
NA
NA
MSDS #1800
10-100L Summary of contents
Page 1
... CHEM-WIK®ROSIN / CHEM-WIK® ROSIN SD CAS# 7440-50-8 8050-09-7 LEL/UEL: Not applicable ACGIH TLV 0.2 g NFPA Solubility in Water: Insoluble Specific Gravity: (Water =1) 8.92 Evaporation Rate: NA Viscosity: NA Percent Volatile: NA Boiling Point: 604F @ 100mm Hg Page MSDS #1800 Wt. % Range 90.0-98.0 2.0-10.0 OSHA PEL ACGIH STEL 1.0 g HMIS ...
Page 2
... ITW CHEMTRONICS SECTION 10: STABILITY AND REACTIVITY Stability - This product is stable. Conditions to Avoid: None known Incompatibility: Do not mix with powdered alkali and alkaline earth metals or strong oxidizing agents. Products of Decomposition: Carbon dioxide, carbon monoxide. Hazardous Polymerization: Will not occur Conditions to Avoid: NA ...