PS21267-AP Powerex Inc, PS21267-AP Datasheet - Page 8

• Manufacturer Part Number: PS21267-AP
• Description: MOD IPM 600V 30A DIP
• Manufacturer: Powerex Inc
• Series: Intellimod™r
• Type: IGBTr

Specifications of PS21267-AP

• Configuration: 3 Phase
• Current: 30A
• Voltage: 600V
• Voltage - Isolation: 2500VDC
• Package / Case: PCB Module
• Dc Collector Current: 30A
• Collector Emitter Voltage Vces: 600V
• Power Dissipation Pd: 55.5W
• Collector Emitter Voltage V(br)ceo: 600V
• Operating Temperature Range: -20°C To +100°C
• No. Of Pins: 26
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8
Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 [phone] www.pwrx.com
PS21267-P / PS21267-AP
Intellimod™ Module
Dual-In-Line Intelligent Power Module
30 Amperes/600 Volts
DIP-IPM Application Circuit (Shown Pins Up)
This symbol indicates
connection to ground
plane.
Component Selection:
Dsgn.
D 1
C 1
C 2
C 3
C 4
C 5
C 6
C 7
C SF
R SF
R SHUNT
R 1
R 2
R 3
Notes:
10) Use high quality, tight tolorance current sensing resistor. Connect resistor as close as possible to the DIP’s
1) To prevent input signal oscillations minimize wiring length to controller (~2cm). Additional RC filtering (C5 etc.) may be
2) Internal HVIC provides high voltage level shifting allowing direct connection of all six driving signals to the controller.
3) F O output is an open collector type. Pull up resistor (R3) should be adjusted to current sink capability of the module.
4) C4 sets the fault output duration and lock-out time. C4 12.2E -6 x t FO , 22nF gives ~1.8ms
5) Boot strap supply component values must be adjusted depending on the PWM frequency and technique.
6) Wiring length associated with R SHUNT , R SF , C SF must be minimized to avoid improper operation of the SC function.
7) R SF , C SF set short-circuit protection trip time. Recommend time constant is 1.5us-2.0us. See application notes.
8) Local decoupling/high frequency filter capacitors must be connected as close as possible to the modules pins.
9) The length of the DC link wiring between C6, C7 , the DIP’s P terminal and the shunt must be minimized to prevent
excessive transient voltages. In particular C7 should be mounted as close to the DIP as possible.
N terminal. Be careful to check for proper power rating. See application notes for calculation of resistance value.
required. If filtering is added be careful to maintain proper dead time. See application notes for details.
+15V
Typ. Value
1A, 600V
10-100uF, 50V
0.22-2.0uF, 50V
10-100uF, 50V
22nF, 50V
100pF, 50V
200-2000uF, 450V
0.1-0.22uF, 450V
1000pF, 50V
1.8k ohm
5-100 mohm
10 ohm
330 ohm
10k ohm
R 2 x 3
R 2
R 2
R 2
R 1
R 1
R 1
C 5 x 3
C 3
C 1
D 1
C 1
D 1
C 1
D 1
C 5
+3.3 to +5V
C 5
C 5
C 4
R 3
+
+
+
+
C 2
C 2
C 2
C 2
C 2
C 2
C 2
Description
Boot strap supply diode – Ultra fast recovery
Boot strap supply reservoir – Electrolytic, long life, low Impedance, 105°C (Note 5)
Local decoupling/High frequency noise filters – Multilayer ceramic (Note 8)
Control power supply filter – Electrolytic, long life, low Impedance, 105°C
Fault lock-out timing capacitor – Multilayer ceramic (Note 4)
Optional input signal noise filter – Multilayer ceramic (Note 1)
Main DC bus filter capacitor – Electrolytic, long life, high ripple current, 105°C
Surge voltage suppression capacitor – Polyester/Polypropylene film (Note 9)
Short circuit detection filter capacitor – Multilayer Ceramic (Note 6, Note 7)
Short circuit detection filter resistor (Note 6, Note 7)
Current sensing resistor - Non-inductive, temperature stable, tight tolerance (Note 10)
Boot strap supply inrush limiting resistor (Note 5)
Optional control input noise filter (Note 1, Note 2)
Fault output signal pull-up resistor (Note 3)
V WFS
V WFB
V VFS
V VFB
V UFS
V UFB
C FO
V NC
V PC
V N1
V P1
V P1
V P1
C IN
W N
W P
U N
V N
F O
U P
V P
C SF
+V CC
+V CC
+V CC
R SF
+V CC LVIC
FAULT
LOGIC
CONDITIONING
INPUT SIGNAL
PROT.
UV
P
N
W
V
U
R SHUNT
MOTOR
C 7
C 6
+
AC LINE
08/10 Rev. 01