RFPIC12F675H-I/SS Microchip Technology, RFPIC12F675H-I/SS Datasheet - Page 41

• Manufacturer Part Number: RFPIC12F675H-I/SS
• Description: IC MCU 1KX14 RF FSK/ASK 20SSOP
• Manufacturer: Microchip Technology
• Series: PIC®r

Specifications of RFPIC12F675H-I/SS

• Frequency: 850MHz ~ 950MHz
• Applications: RKE, Security Systems
• Modulation Or Protocol: ASK, FSK
• Data Rate - Maximum: 40 kbps
• Power - Output: 10dBm
• Current - Transmitting: 14mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Memory Size: 1024 x 14 words Flash, 128 x 8 Byte EEPROM, 64 x 8 Byte SRAM
• Voltage - Supply: 2V ~ 5.5V
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 20-SSOP
• Processor Series: RFPIC12F
• Core: PIC
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 1.75 KB
• Data Ram Size: 64 B
• Interface Type: USB
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 6
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ICE2000
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 4 bit
• For Use With: XLT20SS-1 - SOCKET TRANSITION 18DIP 20SSOPAC124002 - MOD SKT PROMATEII 18SOIC/20SSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Lead Free Status / Rohs Status: Details

7.0
The analog-to-digital converter (A/D) allows conversion
of an analog input signal to a 10-bit binary representa-
tion of that signal. The rfPIC12F675 has four analog
inputs, multiplexed into one sample and hold circuit.
FIGURE 7-1:
7.1
There are two registers available to control the
functionality of the A/D module:
1.
2.
7.1.1
The ANS3:ANS0 bits (ANSEL<3:0>) and the TRISIO
bits control the operation of the A/D port pins. Set the
corresponding TRISIO bits to set the pin output driver
to its high impedance state. Likewise, set the
corresponding ANS bit to disable the digital input
buffer.
7.1.2
There are four analog channels, AN0 through AN3. The
CHS1:CHS0 bits (ADCON0<3:2>) control which
channel is connected to the sample and hold circuit.
7.1.3
There are two options for the voltage reference to the
A/D converter: either V
applied to V
 2003 Microchip Technology Inc.
Note:
ADCON0 (Register 7-1)
ANSEL (Register 7-2)
ANALOG-TO-DIGITAL
CONVERTER (A/D) MODULE
A/D Configuration and Operation
Analog voltages on any pin that is defined
as a digital input may cause the input
buffer to conduct excess current.
ANALOG PORT PINS
CHANNEL SELECTION
VOLTAGE REFERENCE
REF
GP1/AN1/V
is used. The VCFG bit (ADCON0<6>)
GP0/AN0
GP2/AN2
GP4/AN3
REF
A/D BLOCK DIAGRAM
DD
is used, or an analog voltage
CHS1:CHS0
V
REF
V
DD
GO/DONE
VCFG = 0
VCFG = 1
Preliminary
ADON
V
SS
ADC
The output of the sample and hold is connected to the
input of the converter. The converter generates a
binary result via successive approximation and stores
the result in a 10-bit register. The voltage reference
used in the conversion is software selectable to either
V
shows the block diagram of the A/D.
controls the voltage reference selection. If VCFG is set,
then the voltage on the V
otherwise, V
7.1.4
The A/D conversion cycle requires 11 T
of the conversion clock is software selectable via the
ADCS bits (ANSEL<6:4>). There are seven possible
clock options:
• F
• F
• F
• F
• F
• F
• F
For correct conversion, the A/D conversion clock
(1/T
1.6 µs. Table 7-1 shows a few T
selected frequencies.
DD
OSC
OSC
OSC
OSC
OSC
OSC
RC
AD
or a voltage applied by the V
ADFM
) must be selected to ensure a minimum T
(dedicated internal RC oscillator)
/2
/4
/8
/16
/32
/64
ADRESH ADRESL
CONVERSION CLOCK
DD
is the reference.
10
10
rfPIC12F675
REF
pin is the reference;
AD
REF
DS70091A-page 39
calculations for
AD
pin. Figure 7-1
. The source
AD
of