ZMN2430HP-C RFM, ZMN2430HP-C Datasheet - Page 4

• Manufacturer Part Number: ZMN2430HP-C
• Description: MODULE ZIGBEE 2.4GHZ COORDNTR
• Manufacturer: RFM
• Series: ZMNr

Specifications of ZMN2430HP-C

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4
• Applications: Mesh, p2p Networks
• Power - Output: 18dBm
• Sensitivity: -95dBm
• Voltage - Supply: 3.3 V ~ 5.5 V
• Current - Receiving: 33mA
• Current - Transmitting: 130mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Wireless Frequency: 2.4 GHz
• Interface Type: SPI, UART
• Modulation: DSSS, OQPSK
• Operating Voltage: 3.3 VDC to 5.5 VDC
• Output Power: 100 mW
• Operating Temperature Range: - 40 C to + 85 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• For Use With/related Products: CC2430
• Other names: 583-1026

ZMN2430HP I/O Pad Descriptions
Pad
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
1
2
3
4
5
6
7
8
9
SPI_SCLK
UART_RX
SPI_MISO
SPI_MOSI
UART_TX
ADC REF
/RESET
SPI_EN
GPIO0
GPIO4
GPIO5
PWMA
GPIO2
GPIO1
GPIO3
PWMB
RSVD
RSVD
ADCX
ADCY
Name
ADCZ
RFIO
GND
GND
GND
GND
GND
VCC
NC
NC
Power supply and signal ground. Connect to the host circuit board ground.
Reserved pin. Leave unconnected.
Reserved pin. Leave unconnected.
Configurable digital I/O port 0. When configured as an output, the power-on state is also configurable.
Serial data output from UART.
Serial data input to UART.
Configurable digital I/O port 4. When configured as an output, the power-on state is also configurable.
Configurable digital I/O port 5. When configured as an output, the power-on state is also configurable.
Pulse-width modulated output A with internal low-pass filter. Provides a DAC function.
Configurable digital I/O port 2. When configured as an output, the power-on state is also configurable.
Configurable digital I/O port 1. When configured as an output, the power-on state is also configurable.
Configurable digital I/O port 3. When configured as an output, this high current port can sink up to 20 mA. The
power-on output state is also configurable.
Pulse-width modulated output B with internal low-pass filter. Provides a DAC function.
Power supply input, +3.3 to +5.5 Vdc.
Power supply and signal grounds. Connect to the host circuit board ground.
Power supply and signal grounds. Connect to the host circuit board ground.
Active low module hardware reset. Hold this input low when the power supply input is less than 2.7 Vdc.
7-bit to 12-bit ADC input 0. ADC full scale reading can be referenced to the module’s +3.3 V regulated suppy or
to the ADC’s internal +2.5 V reference.
7-bit to 12-bit ADC input 1. ADC full scale reading can be referenced to the module’s +3.3 V regulated suppy or
to the ADC’s internal +2.5 V reference.
SPI port data input.
SPI port data output.
Active-low enable output for SPI bus devices.
SPI port clock signal.
7-bit to 12-bit ADC input 2. ADC full scale reading can be referenced to the module’s +3.3 V regulated suppy or
to the ADC’s internal +2.5 V reference.
Module’s +3.3 V regulated suppy, used for ratiometric ADC readings. Current drain on this output should be no
greater than 5 mA.
No connection.
No connection.
RF ground. Connect to the host circuit board ground plane, and to shield when using coaxial cable.
RF port. Connect the antenna to this port with a 50 Ω stripline or semi-rigid coaxial cable.
RF ground. Connect to the host circuit board ground plane, and to shield when using coaxial cable.
4
Description