RN-24E Roving Networks Inc, RN-24E Datasheet - Page 8

• Manufacturer Part Number: RN-24E
• Description: SUPERMODULE BLUETOOTH SMA JACK
• Manufacturer: Roving Networks Inc

Specifications of RN-24E

• Frequency: 2.4GHz
• Data Rate - Maximum: 721kbps
• Modulation Or Protocol: Bluetooth v2.0+EDR, Class 1 & 2
• Applications: Bluetooth v2.0
• Power - Output: 4dBm
• Sensitivity: -80dBm
• Voltage - Supply: 4 V ~ 24 V
• Current - Receiving: 40mA
• Current - Transmitting: 40mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: SMA
• Package / Case: Module
• Wireless Frequency: 2.402 GHz to 2.48 GHz
• Interface Type: UART
• Data Rate: 240 Kbps to 300 Kbps
• Modulation: FHSS, GFSK
• Operating Voltage: 3.3 V
• Antenna: SMA Jack
• Board Size: 20.32 mm x 50.8 mm x 4.08 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 740-1009

4 Command Reference
1.2 SET Commands
www.rovingnetworks.com
All commands are either one or two characters and can be upper or lower case. Arguments for commands are
delimited by a comma. Commands take decimal input except where noted. Text data, such as Bluetooth
name, and pin code, are case sensitive. Commands fall into five general categories:
SET COMMANDS
GET COMMANDS
CHANGE COMMANDS
ACTION COMMANDS
GPIO COMMANDS
All set commands do not take effect until after the module has been rebooted.
S7,<1,0>
SA,<1,0>
SB,<timer>
SC,<hex word>
SD,<hex word>
809 University Avenue
To set the Class of Device (COD) to 0x1F0123 use the commands
Device Class (four hex values, major and minor in a 16 bit word, used with service
1= 37ms, 2=18.5ms, 3=12ms, 4=9ms, 5= 7ms, 6=6ms.
7 bit data mode. 1 to enable, 0 to disable. (setting can be seen with the “d”
command).
Authentication. 1 to enable, 0 to disable. This will force authentication when any
remote device attempts to connect. Regardless of this setting, if a remote device
forces authentication, this device will respond with the stored pin code. Once a
remote device has exchanged pin codes with this device, a link key will be stored for
future use. Up to 8 keys are automatically and permanently in flash on the device, in
a first in, first out fashion.
Send BREAK. This is an immediate command, which can send a BREAK signal on
the TX . The timer is used to send a variable length BREAK signal.
Timer value
Example : “SB,2” sends a 18.5 millisecond break signal.
Service Class (four hex values, 11 used, this is used with Device Class command
below to create the 24 bit Class of Device number. Note the service class is
interpreted by the inquiring device to determine the service. To see a complete
listing of available Bluetooth service classes check the Bluetooth SIG web site.
Example : “SC,0002”
class above)
Example : “SD,8040”
•
Los Gatos, CA 95032
store information to flash, changes take effect after power cycle or reboot
retrieve and display the stored information
temporarily change the value of serial baudrate, parity, etc.
perform action such as inquiry, connect, etc.
configure and manipulate GPIO signals
Break length (in milliseconds)
~ 8 ~
•
Tel [phone]
rn-bluetooth-um Version 4.77 1/24/2011
Advanced User Manual
• [e-mail]