XC09-009NSC Digi International/Maxstream, XC09-009NSC Datasheet - Page 30
![no-image](/images/no-image-200.jpg)
XC09-009NSC
Manufacturer Part Number
XC09-009NSC
Description
MOD RF 900MHZ 9600BPS W/RPSMA
Manufacturer
Digi International/Maxstream
Series
9XCite™r
Specifications of XC09-009NSC
Frequency
900MHz
Data Rate - Maximum
9.6kbps
Modulation Or Protocol
FHSS, FSK
Power - Output
6dBm
Sensitivity
-108dBm
Voltage - Supply
2.85 V ~ 5.5 V
Current - Receiving
45mA
Current - Transmitting
55mA
Data Interface
PCB, Through Hole
Antenna Connector
RP-SMA
Operating Temperature
0°C ~ 70°C
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Applications
-
Memory Size
-
9XCite™ OEM RF Module – Product Manual v2.1 [2007.01.04]
4.1.2. Channel (ATHP)
4.1.3. Destination Address (ATDT) and Address Mask (ATMK)
Packet-based Radio Modems
Address Mask
Channels provide a network layer from which channels can be used for isolation. HP (Channel)
Parameter is used to define channel values.
Hopping Channel Mode: HP Parameter value range is 0 through 6
Single Frequency Channel Mode: HP range is 0 through 0x18 (decimal range: 0 - 24)
In "Hopping Channel Mode", each channel utilizes a different pseudo-random hopping sequence to
navigate through shared hopping channels. In the event that two modems from different networks
collide on a channel, the two modems will jump to separate channels on the next hop. Multiple
modem pairs can operate in the same vicinity with minimal interference from each other.
XCite Destination Addresses and Masks provide the means to set up global or local addresses for
establishing modem groups, subnets, etc. The Destination Address network layer provides for
more granular isolation of radio modems. The XCite Destination Addresses and Masks can be used
to:
Each radio modem in a network can be configured with a 16-bit Destination Address to establish
selective communications within a network. This address is set to one of 65535 values using DT
(Destination Address) Command. The default Destination Address is 0.
All radio modems with the same Destination Address can transmit and receive data among them-
selves. Radio modems having different Destination Addresses still detect and listen to the data (in
order to maintain network synchronization); however, the data is discarded data rather than pass-
ing on through the DO pin.
XCite Radio Modems are packet based. This means all data shifted into one modem is packetized
and sent out the antenna port. Because XCite modems use a peer-to-peer architecture, all
modems on the same channel (ATHP) will receive the packet and decide whether to pass it to the
host or to throw it away. Each transmitted packet contains information about the transmitting
modem.
Any modem that receives a packet will check the address values and decide what to do with the
packet. The options are as follows:
The mask parameter can be used to allow a base modem to receive data from a range of
addresses. It may also be used to configure "subnets" of modems that communicate in a group
together.
Refer to the “Bit-wise AND Truth” table for the Pseudo 'C' Code that qualifies the Destination
Addresses and address masks.
The Pseudo Code uses the bit-wise "AND" operation, "&". This operation is performed bit by bit on
each of the 16 bits in the TXDT, RXDT and RXMK parameters.
© 2007 MaxStream, Inc.
• Set up point-to-point and point-to-multipoint network configurations
• Provide greater flexibility in establishing modem groups, subnets, etc.
• Receive the packet as a global packet
• Receive the packet as a local packet
• Discard the packet
30