ENW-C9A04N4E Panasonic - ECG, ENW-C9A04N4E Datasheet - Page 18
![MODULE ZIGBEE 2.4GHZ EMBER SMD](/photos/14/20/142048/enw-c9a04n4e_sml.jpg)
ENW-C9A04N4E
Manufacturer Part Number
ENW-C9A04N4E
Description
MODULE ZIGBEE 2.4GHZ EMBER SMD
Manufacturer
Panasonic - ECG
Series
PAN4570r
Specifications of ENW-C9A04N4E
Frequency
2.4GHz
Modulation Or Protocol
802.15.4 Zigbee
Applications
General Purpose
Power - Output
3dBm
Sensitivity
-97dBm
Voltage - Supply
2.1 V ~ 3.6 V
Current - Receiving
37.5mA
Current - Transmitting
41.5mA
Data Interface
PCB, Surface Mount
Memory Size
128kB Flash, 5kB SRAM
Antenna Connector
PCB, Surface Mount
Operating Temperature
-40°C ~ 85°C
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Data Rate - Maximum
-
Other names
ENWC9A04N4E
P13687TR
PAN4570-SMD
P13687TR
PAN4570-SMD
CLASSIFICATION
Einstufung
SUBJECT
Thema
CUSTOMER’S CODE
PAN4570
20 RECOMMENDED LAND PATTERN
HIGH FREQUENCY PRODUCTS DIVISION
Dimensions in mm.
The land pattern dimensions above can serve as a guidance, but this information is given without
any legal responsibility.
We recommend the use of the same pad dimensions for the solder paste screen as for the copper
pads, but slight different measures and shapes of the solder paste screen cutouts might be
optimum depending on your soldering process, for example on the chosen solder paste screen
thickness. The solder screen thickness depends on your soldering technology, we recommend
120µm to 150µm.
IMPORTANT:
The bottom side of PAN4570 is fully coated, nevertheless no copper, such as through hole vias,
planes or tracks on your board component layer should be located below PAN4570 in order to
avoid short cuts. In cases where a track or through hole via has to be located under the module it
has to be kept away from PAN4570 via holes. The PAN4570 multilayer pcb contains a inner rf
shielding ground plane, therefore no pcb copper plane directly below PAN4570 is needed.
If the integrated antenna version of PAN4570 is used, it has to be mounted on a board with a full
copper plane layer of at least 50mm x 50mm, else the radiation performance is degraded. Place
the antenna on the edge of your carrier board and avoid conductive or shielding parts other than
the carrier board in the near of the integrated antenna.
Empfohlenes Land Pattern
PANASONIC ELECTRONIC DEVICES
5.0
(EUROPE) GmbH
Module Business
MODEM FOR IEEE802.15.4 (ZIGBEE)
“ZigBee” Modem“ (IEEE802.15.4)
PRODUCT SPECIFICATION
26,5 mm (Module Lenght)
PANASONIC’S CODE
ENWCZA0xyzE
Produktspezifikation
1.00
Top View
48 x 1.00
4 x P1 = 0.70
12 x 1.00 x 1.00
36 x 1.00 x 1.30
Sign "1" on the Module
Pad #1
Pad #2
(Bottom Side)
APPROVED
genehmigt
Pin 1
40 x P2 = 0.40
2.00
No.
DS-4570-2400-102
PAGE
Seite
DATE
Datum
CHECKED
geprüft
0.20
1.30
16.03.2007
18 of 30
DESIGNED
erstellt
REV.
07