F2M03GLA-S01 Free2Move, F2M03GLA-S01 Datasheet
F2M03GLA-S01
Specifications of F2M03GLA-S01
Related parts for F2M03GLA-S01
F2M03GLA-S01 Summary of contents
Page 1
... CE and FCC, which give fast and easy Plug-and-Go implementation and short time to market. The F2M03GLA comes with an on board highly efficient omni-directional antenna that simplifies the integration for a developers Bluetooth™ solution. The high output power combined with ...
Page 2
... Low power Bluetooth™ Module with antenna- F2M03GLA Table of contents 1 Device pinout .........................................................................................................................3 2 Device terminal functions .....................................................................................................4 3 Electrical Characteristics ......................................................................................................5 4 Radio Characteristics ............................................................................................................8 5 Firmware versions .................................................................................................................9 5.1 Wireless UART ............................................................................................................................. 11 5.2 HCI ................................................................................................................................................ 16 6 Device terminal description ................................................................................................19 6.1 UART Interface ............................................................................................................................. 19 6.2 USB Interface................................................................................................................................ 21 6.3 Serial Peripheral Interface ...
Page 3
... Low power Bluetooth™ Module with antenna- F2M03GLA 1 Device pinout Pinout of the F2M03GLA seen from the component side [TOP VIEW] Datasheet © 2006 Free2move AB Rev: c Page 3(3) ...
Page 4
... Low power Bluetooth™ Module with antenna- F2M03GLA 2 Device terminal functions Ground Pin GND 1,16,17,32 Power supplies Pin +VCC 31 Analog I/O Pin AIO(0) 18 AIO(1) 19 Reset Pin RESET 30 Test and debug Pin SPI MISO 3 SPI CSB 5 SPI CLK 2 SPI MOSI 4 UART Pin ...
Page 5
... Storage Temperature Breakdown supply voltage Recommended Operating Conditions* Rating Operating temperature range Supply voltage *F2M03GLA meet the Bluetooth v2.0+EDR specification when used in the recommended operating condition. Input/Output Terminal Characteristics Digital Terminals Input Voltage input logic level low, 2.7V ≤ VDD ≤ 3.0V V ...
Page 6
... Low power Bluetooth™ Module with antenna- F2M03GLA Input/Output Terminal Characteristics (Continued) Auxiliary ADC, 8-bit resolution Resolution Input voltage range (LSB size = 1.8/255= 7.1mV) Accuracy INL (Guaranteed monotonic) DNL Offset Gain Error Input Bandwidth Conversion time Sample rate* *The ADC is accessed through the VM function. The sample rate given is achieved as a part of this function Average current consumption VDD = 3 ...
Page 7
... Low power Bluetooth™ Module with antenna- F2M03GLA Peak current consumption VDD = 3.3V Temperature = 20 Mode Peak consumption during RF peaks Leakage current VDD = 3.3V Temperature = 20 Mode Reset LOW Deep sleep Datasheet o C Typ o C © 2006 Free2move AB Unit 75 mA Typ Unit 200 µ ...
Page 8
... Operating Frequency Transmit Power Sensitivity at 0.1% BER Note: The F2M03GLA has a maximum transmit power of +8dBm and is certified according to the Bluetooth v2.0+EDR specification as a Class1 device though possible to restrict the maximum transmit power to comply with either a Class2 or Class3 device upon configuration. Bluetooth Specification ...
Page 9
... Low power Bluetooth™ Module with antenna- F2M03GLA 5 Firmware versions F2M03 is supplied with Bluetooth stack firmware, which runs on the internal RISC micro controller of the Bluetooth module. This chapter includes an overview of the different options for more in depth information please use separate firmware datasheets provided by Free2move. ...
Page 10
... Low power Bluetooth™ Module with antenna- F2M03GLA Application Bluetooth stack HCI Host F2M03 HCI LINK MANAGER BASEBAND and RF HCI, (Two-Processor Architecture) Wireless UART Free2move’s Wireless UART (WU) firmware is intended to replace the serial cable(s) connecting portable and/or fixed electronic devices. Key features are robustness, high configurability, high security, low complexity and low power ...
Page 11
... Low power Bluetooth™ Module with antenna- F2M03GLA 5.1 Wireless UART Free2move’s Wireless UART (WU) firmware is intended to replace the serial cable(s) connecting portable and/or fixed electronic devices. Key features are robustness, high configurability, high security, low complexity and low power. The WU firmware is compliant with the Bluetooth Serial Port Profile (SPP) for setting up emulated serial cable connections between connected devices ...
Page 12
... Low power Bluetooth™ Module with antenna- F2M03GLA 5.1.1 General I/O General I/O interfaces are used for different purposes between the WU firmware and the Host: • Asynchronous data interface – configuration of the WU firmware or exchange transparent digital information between the connected Bluetooth devices. ...
Page 13
... Low power Bluetooth™ Module with antenna- F2M03GLA 5.1.2 Settings The default settings allow the user to communicate via Bluetooth, without sending any configuration commands, as soon as a successful connection has been established. Information sent and received on the serial interface of the WU unit at 38400 bps is transmitted transparently between the two connected devices ...
Page 14
... Low power Bluetooth™ Module with antenna- F2M03GLA Software / Hardware Reboot This option gives the ability to be able to reboot the module via software commands. Inquiry Search for other Bluetooth devices in the neighborhood. There are three configuration parameters: • How many seconds the search should be active • ...
Page 15
... Low power Bluetooth™ Module with antenna- F2M03GLA 5.1.3 Performance The WU firmware is a complete on-chip application; limited resources restrict the maximum throughput. The table below shows the maximum achieved throughput when streaming data between two connected WU v4.00 devices at close range. Direction ...
Page 16
... Low power Bluetooth™ Module with antenna- F2M03GLA 5.2 HCI In this implementation the internal processor of the module runs the Bluetooth stack up to the Host Controller Interface (HCI) as specified in the Bluetooth specification V1.1. The external host processor must provide all upper Bluetooth stack layers. Free2move do not offer a host stack solution for an external Host. ...
Page 17
... Low power Bluetooth™ Module with antenna- F2M03GLA • Standard Bluetooth power saving mechanisms: Hold, Sniff and Park modes, including “Forced Hold” • Dynamic control of peers’ transmit power via LMP • Master/Slave switch • Broadcast • Channel quality driven data rate (CQDDR) • ...
Page 18
... Low power Bluetooth™ Module with antenna- F2M03GLA 5.2.2 Extra Functionality The firmware extends the standard Bluetooth functionality with the following features: • Supports BlueCore Serial Protocol (BCSP proprietary, reliable alternative to the standard Bluetooth (H4) UART Host Transport. • Provides a set of approximately 50 manufacturer-specific HCI extension commands. This command set (called BCCMD – ...
Page 19
... Low power Bluetooth™ Module with antenna- F2M03GLA 6 Device terminal description 6.1 UART Interface The F2M03 Bluetooth module’s Universal Asynchronous Receiver Transmitter (UART) interface provides a simple mechanism for communicating with other serial devices using the RS232 standard Four signals are used to implement the UART function, as shown in the figure above. When F2M03 is connected to another digital device, UART_RX and UART_TX transfer data between the two devices ...
Page 20
... Low power Bluetooth™ Module with antenna- F2M03GLA The UART interface is capable of resetting the Free2move module upon reception of a break signal. A Break is identified by a continuous logic low on the UART_RX terminal, as shown in figure below. If tBRK is longer than a special value, defined by the Free2move firmware a reset will occur. This feature allows a host to initialise the system to a known state ...
Page 21
... Low power Bluetooth™ Module with antenna- F2M03GLA 6.2 USB Interface F2M03 contain a full-speed (12Mbits/s) USB interface, capable of driving a USB cable directly. No external USB transceiver is required. The device operates as a USB peripheral, responding to requests from a master host controller such as a PC. Both the OHCI and the UHCI standards are supported. The set of USB endpoints implemented behave as specified in the USB section of the Bluetooth specification v2 ...
Page 22
... Low power Bluetooth™ Module with antenna- F2M03GLA 6.2.5 Bus-Powered Mode In bus-powered mode the application circuit draws its current from the 5V VBUS supply on the USB cable. F2M03 negotiates with the PC during the USB enumeration stage about power consumption. Bus-Powered mode is not supported in the default firmware of the HCI-firmware When selecting a regulator, be aware that VBUS may go as low as 4 ...
Page 23
... Low power Bluetooth™ Module with antenna- F2M03GLA 6.2.6 Suspend Current USB devices that run off VBUS must be able to enter a suspended state, whereby they consume less that 0.5mA from VBUS. The voltage regulator circuit itself should draw only a small quiescent current (typically less than 100µ ...
Page 24
... Low power Bluetooth™ Module with antenna- F2M03GLA 6.2.9 USB 1.1 Compliance The Bluetooth chip on the F2M03 is qualified to the USB specification v1.1, details of which are available from http://www.usb.org. The specification contains valuable information on aspects such as PCB track impedance, supply inrush current and product labeling. ...
Page 25
... Low power Bluetooth™ Module with antenna- F2M03GLA 6.3 Serial Peripheral Interface F2M03 is a slave device that uses terminals SPI_MOSI, SPI_MISO, SPI_CLK and SPI_CSB. This interface is used for program emulation/debug and IC test also the means by which the F2M03 flash may be programmed, before any 'boot' program is loaded. ...
Page 26
... Low power Bluetooth™ Module with antenna- F2M03GLA 6.5 PCM Pulse Code Modulation (PCM) is the standard method used to digitise audio (particulary voice) for transmission over digital communication channels. Through its PCM interface, F2M03 has hardware support for continual transmission and reception of PCM data, thus reducing processor overhead for wireless headset and other audio applications ...
Page 27
... Low power Bluetooth™ Module with antenna- F2M03GLA 6.5.1 PCM Interface Master/Slave When configured as the Master of the PCM interface, F2M03 generates PCM_CLK and PCM_SYNC. F2M03 as PCM Interface Master When configured as the Slave of the PCM interface, F2M03 accepts PCM_CLK rates up to 2048kHz ...
Page 28
... Low power Bluetooth™ Module with antenna- F2M03GLA 6.5.2 Long Frame Sync Long Frame Sync is the name given to a clocking format that controls the transfer of PCM data words or samples. In Long Frame Sync, the rising edge of PCM_SYNC indicates the start of the PCM word. When F2M03 is configured as PCM Master, generating PCM_SYNC and PCM_CLK, then PCM_SYNC is 8-bits long ...
Page 29
... Low power Bluetooth™ Module with antenna- F2M03GLA 6.5.4 Multi-Slot Operation More than one SCO connection over the PCM interface is supported using multiple slots three SCO connections can be carried over any of the first four slots. Multi-slot Operation with Two Slots and 8-bit Companded Samples 6 ...
Page 30
... Low power Bluetooth™ Module with antenna- F2M03GLA 6.5.6 Slots and Sample Formats F2M03 can receive and transmit on any selection of the first four slots following each sync pulse. Slot durations can be either clock cycles. Durations of 8 clock cycles may only be used with 8-bit sample formats. Durations of 16 clocks may be used with 16-bit sample formats. F2M03 supports 13-bit linear, 16-bit linear and 8-bit µ ...
Page 31
... Low power Bluetooth™ Module with antenna- F2M03GLA 6.5.8 PCM Timing Information PCM Master Timing Symbol f PCMCLK frequency mclk - PCM_SYNC frequency (1) t PCM_CLK high mclkh ( PCM_CLK low mclk Delay time from PCM_CLK high to t dmclksynch PCM_SYNC high Delay time from PCM_CLK high to valid ...
Page 32
... Low power Bluetooth™ Module with antenna- F2M03GLA PCM Slave Timing Symbol f PCM clock frequency (Slave mode: input) sclk f PCM clock frequency (GCI mode) sclk t PCM_CLK low time sclkl t PCM_CLK high time sclkh Hold time from PCM_CLK low to t hsclksynch PCM_SYNC high ...
Page 33
... Low power Bluetooth™ Module with antenna- F2M03GLA 6.6 PIOs The F2M03GLA have 10 programmable general-purpose I/O ports PIO[11:2] and two analog I/O ports AIO[1:0]. PIO lines can be configured through software to have either weak or strong pull-ups or pull- downs. All PIO lines are configured as inputs with weak pull-downs at reset. ...
Page 34
... XC6209B332MR from Torex or TPS73633DBVTG4 from Texas Instrument 6.7.2 Reset The F2M03GLA has an active low reset (pin nr: 30). The reset pin MUST be connected to either a reset- circuit (voltage monitor) such as the TC1270ASVRCTR, MAX811S, DS1818 or using an I/O from a microcontroller. Reset cannot be done with a R-C network recommended to used one of the reset circuits mentioned above. Special considerations must be taken when using an I/O from a microcontroller ...
Page 35
... Low power Bluetooth™ Module with antenna- F2M03GLA 7 Application information 7.1 Recommended land pattern 0.8 Solder pad Recommended extended pad for manual soldering Restricted area for ground planes or other components • Pad size: 0.8x1.2mm, • Solder mask opening 0.9x1.3mm • Pitch: 1.27mm (50mil) ...
Page 36
... Low power Bluetooth™ Module with antenna- F2M03GLA 7.2 Layout guidelines The module uses bottom pads for soldering optimized for an automatic solder line also possible to solder the module manually by using hot air soldering. For manual soldering solder pads may in some situation be made slightly larger to allow easier heating process. ...
Page 37
... Low power Bluetooth™ Module with antenna- F2M03GLA 7.3 Typical application schematic Typical application schematic for F2M03GLA when using the Wireless UART firmware Datasheet © 2006 Free2move AB Rev: c Page 37(37) ...
Page 38
... Low power Bluetooth™ Module with antenna- F2M03GLA 8 Package information F2M03GLA Physical size [mm]: Length: 28.5 Width: 15.2 Height: 2.1 Weight: 1.2g Datasheet © 2006 Free2move AB Rev: c Page 38(38) ...
Page 39
... F2M03GLA has passed the Bluetooth Qualification/Certification process as specified within the Bluetooth Specifications and as required within the PRD 2.0. QDID: B012541 9.2 CE F2M03GLA complies with the requirements of R&TTE Directive 1999/5/CE, the European Community Directive 73/23/EEC and 93/68/EEC. • EN 300 328 • EN 301 489-1/-17 • ...
Page 40
... Low power Bluetooth™ Module with antenna- F2M03GLA 9.3 FCC FCC-B Radio Frequency Interference Statement This deceive has been tested and found to comply with the limits for a Class-B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in commercial environment ...
Page 41
... Low power Bluetooth™ Module with antenna- F2M03GLA 10 RoHS Statement F2M03GLA meet the requirements of Directive 2002/95/EC of the European Parliament and of the Council on the Restriction of Hazardous Substance (RoHS). The module is assembled solely using RoHS compliant components. Datasheet © 2006 Free2move AB Rev: c Page 41(41) ...
Page 42
... Low power Bluetooth™ Module with antenna- F2M03GLA 11 Tape and Reel information 11.1 Package Tape dimensions 11.2 Reel dimensions A 330.0 max B 1.5 min C 13.0±0.2 D 20.2 min N 100.0 W1 44.4 +2.0 –0.0 W2 50.4 max Datasheet © 2006 Free2move AB Rev: c Pulling direction W2 W1 ...
Page 43
... Low power Bluetooth™ Module with antenna- F2M03GLA 12 Ordering information The F2M03GLA is available for delivery in volumes. Part nr: F2M03GLA-S01 Low power Bluetooth module with antenna and Wireless UART firmware v4. (SPP) F2M03GLA-S04 Low power Bluetooth module with antenna and HCI firmware (USB-interface, Self-powered) Please use our website: www ...
Page 44
... Low power Bluetooth™ Module with antenna- F2M03GLA 13 Document history Date Revision Reason for Change Added certification, tape & reel, JUNE 2007 c document. JAN 2007 b Small technical changes of the document. NOV 2006 a Original Publication of this document. Datasheet_F2M03GLA_rev_c.pdf Datasheet power consumtion information and minor other changes in the ...
Page 45
... Low power Bluetooth™ Module with antenna- F2M03GLA Acronyms and definitions Term: Bluetooth A set of technologies providing audio and data transfer over short-range radio ACL Asynchronous Connection-Less. A Bluetooth data packet. AC Alternating Current A-law Audio encoding standard API Application Programming Interface BCSP BlueCore™ Serial Protocol BER Bit Error Rate ...
Page 46
... Low power Bluetooth™ Module with antenna- F2M03GLA Contact information For support questions please contact your local dealer For other purposes use: info@free2move.net Website: www.free2move.net Local dealer/distributor The information given herein includes text, drawings, illustrations and schematics that are believed to be reliable. However, Free2move makes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use ...