ZICM2410P2-1 CEL, ZICM2410P2-1 Datasheet - Page 15
![MODULE 802.15.4 W/TRACE ANT](/photos/39/39/393965/zicm2410p2_sml.jpg)
ZICM2410P2-1
Manufacturer Part Number
ZICM2410P2-1
Description
MODULE 802.15.4 W/TRACE ANT
Manufacturer
CEL
Series
MeshConnect™r
Datasheet
1.ZICM2410P2-KIT1-1.pdf
(16 pages)
Specifications of ZICM2410P2-1
Frequency
2.4GHz
Data Rate - Maximum
1Mbps
Modulation Or Protocol
802.15.4 Zigbee
Applications
Home/Building Automation, Industrial Control
Power - Output
20dBm
Sensitivity
-103.5dBm
Voltage - Supply
2.1 V ~ 3.3 V
Current - Receiving
38mA
Current - Transmitting
175mA
Data Interface
Pads for Pins
Memory Size
96kB Flash, 8 kB RAM
Antenna Connector
On-Board, Trace
Operating Temperature
-40°C ~ 85°C
Package / Case
Module
Wireless Frequency
2.4 GHz
Interface Type
I2C, SPI, UART
Security
128 bit AES
Operating Voltage
3.3 V
Output Power
20 dBm
Antenna
PCB Trace
Operating Temperature Range
- 40 C to + 85 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
AGENCY CERTIFICATIONS
IC Certification — Industry Canada Statement
The term "IC" before the certification / registration number only signifies that the Industry Canada technical specifications
were met.
Section 14 of RSS-210
The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in
excess of Health Canada limits for the general population. Consult Safety Code 6, obtainable from Health Canada's
website:
CE Certification — Europe
The MeshConnect RF module has been tested and certified for use in the European Union.
OEM Responsibility to the European Union Compliance Rules
If the MeshConnect module is to be incorporated into a product, the OEM must verify compliance of the final product to the
European Harmonized EMC and Low-Voltage / Safety Standards. A Declaration of Conformity must be issued for each of
these standards and kept on file as described in Annex II of the R&TTE Directive.
The manufacturer must maintain the user's guide and adhere to the settings described in the manual for maintaining
European Union Compliance. If any of the specifications are exceeded in the final product, the OEM is required to
make a submission to the notified body for compliance testing.
OEM Labeling Requirements
The `CE' mark must be placed on the OEM product in a visible location.
The CE mark shall consist of the initials “CE” with the following form:
SHIPMENT, HANDLING, AND STORAGE
Shipment
The MeshConnect Modules are delivered in trays of 28.
Handling
The MeshConnect Modules are designed and packaged to be processed in an automated assembly line.
Warning
protection may destroy or damage the module permanently.
Warning
tions and precautions are summarized in Section 2.1. Read carefully to prevent permanent damage due to moisture intake.
Moisture Sensitivity Level (MSL)
MSL 3, per J-STD-033
Storage
Storage/shelf life in sealed bags is 12 months at <40°C and <90% relative humidity.
· If the CE marking is reduced or enlarged, the proportions given in the above graduated
· The CE mark must be a minimum of 5mm in height
· The CE marking must be affixed visibly, legibly, and indelibly. Since the 2400 - 2483.5 MHz
drawing must be adhered to.
band is not harmonized by a few countries throughout Europe, the Restriction sign must be
placed to the right of the “CE” marking as shown in the picture
http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/99ehd-dhm237/index-eng.php
The MeshConnect Modules contain highly sensitive electronic circuitry. Handling without proper ESD
According to JEDEC ISP, the MeshConnect Modules are moisture-sensitive devices. Appropriate handling instruc-
(Continued)
MeshConnect™ Module Series
Page 15