MRX-002-433DR-B Radios Inc, MRX-002-433DR-B Datasheet - Page 5
![MODULE RECEIVER 433MHZ 18DIP](/photos/14/17/141753/mrx-002-433dr-b_sml.jpg)
MRX-002-433DR-B
Manufacturer Part Number
MRX-002-433DR-B
Description
MODULE RECEIVER 433MHZ 18DIP
Manufacturer
Radios Inc
Datasheet
1.MRX-002-433DR-B.pdf
(10 pages)
Specifications of MRX-002-433DR-B
Frequency
433MHz
Sensitivity
-95dBm
Data Rate - Maximum
10 kbps
Modulation Or Protocol
AM, OOK
Applications
Garage Openers, RKE, Security Alarms
Current - Receiving
2mA
Data Interface
PCB, Through Hole
Antenna Connector
Through Hole
Voltage - Supply
5 V ~ 16 V
Operating Temperature
0°C ~ 70°C
Package / Case
18-DIP Module
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Features
-
Memory Size
-
Other names
694-1003
UHF AM RECEIVER MODULE
MRX-002
4,5,6,7,8
1,2,3
DIP
18
17
16
15
14
13
12
11
10
9
Pin Number
Surface Mount
2,3,4,5,6
MRX-002, 433.92MHz Fixed, 1250bps Bandwidth
7,8,9
Typical Application Schematic
10
11
12
13
14
15
16
17
18
1
SEL0 SEL1 Sweep Mode (bps) Fixed Mode (bps)
1
2
3
4
5
6
7
8
9
*Note: 1=VCC, 0=GND
0
1
0
1
N/C
N/C
N/C
GND
GND
GND
GND
GND
ANT
Programmable Bandwidth Configurations
WAKEB Wakeup output (active-low) that indicates detection of an
REG-EN In a regulated module, this pin powers on the module with a 2-
SWEN Controls the operating mode of the receiver. When high, the
Name
SHUT
SEL1
SEL0
+VIN
Gnd
+5V
Pin
N/C
Ant
DO
0
0
1
1
MRX-002
MRX-002
U1
U1
This is the receive RF input, internally ac-coupled. Connect this
pin to the receive antenna.
Ground
No Connect
Data output pin.
receiver is in sweep mode. When low, the module operates as a
conventional single-conversion superheterodyne receiver (fixed
mode) - this is the recommended mode of operation. This pin is
internally pulled-up to VCC.
Programs desired Demodulator Filter Bandwidth. This pin is
internally pulled-up to VCC. See Table 1.
Programs desired Demodulator Filter Bandwidth. This pin is
internally pulled-up to VCC. See Table 1.
incoming RF signal. Pin goes low when a constant RF carrier is
detected.
Shutdown-mode logic-level control input. Pull low to enable the
receiver. Internally pulled-up to VCC.
16V supply input. Pulling this pin low disables module. In a non-
regulated module, this is a no connect.
In a regulated module, this is a 5V output from the onboard
regulator when REG-EN is high (2-16V). In a non-regulated
module, this is the 4.75V to 5.5V power supply input.
In a regulated module, this is the power supply pin of the module.
Input 5-16V to power a regulated module. In a non-regulated
module, this is a no connect.
REG-EN
WAKEB
SWEN
Pin Detail
SHUT
SEL1
SEL0
+VIN
1250
2500
5000
625
+5V
Table 1
DO
-Page 5-
18
17
16
15
14
13
12
11
10
Data Out to MCU
GND
GND
GND
Wake Out to MCU
GND
+2V-16V In
+5V Output
+5V-16V In
10000
1250
2500
5000
Description
MCU