CME6005-TCQH C-Max, CME6005-TCQH Datasheet - Page 3

• Manufacturer Part Number: CME6005-TCQH
• Description: IC RECEIVER RC BICMOS 16-SSOP
• Manufacturer: C-Max

Specifications of CME6005-TCQH

• Frequency: 40kHz ~ 120kHz
• Sensitivity: -115dBm
• Modulation Or Protocol: UTC - Universal Time Code
• Applications: Radio Controlled Time
• Current - Receiving: 100µA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Voltage - Supply: 1.2 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-SSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Memory Size: -
• Data Rate - Maximum: -
• Other names: 561-1013-2; CME6005-TCQH; CME6005-TSQH; CME6005-TSQH

C-MAX
6- Pad Layout
PIN Description
IN1, IN2
A ferrite antenna is connected between IN 1 and IN 2. For high sensitivity, the Q factor of the antenna circuit
should be as high as possible. Please note that a high Q factor requires temperature compensation of the
resonant frequency in most cases. We recommend a Q factor between 40 and 150, depending on the
application. An optimal signal-to-noise ratio will be achieved by a resonator resistance of 40 kΩ to 100 kΩ.
QOUT, QIN , QC
In order to achieve a high selectivity, a crystal is connected between the Pins QOUT and QIN. It is used with
the serial resonant frequency according to the time-code transmitter and acts as a serial resonator. Up to 2
crystals can be connected parallel between QOUT and QIN. For one crystal, the given parallel capacitor of
the filter crystal (about 1.4 pF) is internally compensated so that the bandwidth of the filter is about 10 Hz.
For two crystals, an additional external capacitor with the value of about 1.4 pF has to be connected parallel
between QC and QIN. The impedance of QIN is high. Parasitic loads have to be avoided.
DEM
Demodulator output. To ensure the function, an external capacitor has to be connected at this output.
HLD
AGC hold mode: HLD high (V
AGC voltage. This can be used to prevent the AGC from peak voltages, created by e.g. a stepper motor
PK
Peak detector output. An external capacitor has to be connected to ensure the function of the AGC
regulation. The value of the capacitance influences the AGC regulation time.
NOTE: To realize a good regulation timing of the demodulator and the peak detector the value of the
capacitors at DEM and PK have to be changed for the different protocols.
Y-axis
QOUT
CME6005
GND
VCC
IN 2
IN 1
QIN
SPEC No.
QC
Reference point (%)
13
X-axis
2
3
4
5
6
1
Time Solutions
Revision
A.8
Figure 2. Pad layout
7
HLD
12
11
10
9
8
= V
04.12.06
DEM
HLD
PK
PON
TCO
TCON
CC
State
) sets normal function, HLD low (V
Th e PA D co or d in a te s
are referred to the left
bottom point of the contact
window
03.05.2007
C-MAX printed
QOUT
GND
VCC
IN 2
IN 1
QIN
QC
HLD
NC
Datasheet
Figure 3. Pin layout SSO16
Pin Layout SSO16
2
3
4
5
6
7
8
1
= 0) holds for a short time the
English
Version
CME6005
FB
CME6005
16
15
14
13
12
10
11
9
NC
NC
DEM
HLD
PK
PON
TCO
TCON
3 of 15
Page