SI4311-B10-GM Silicon Laboratories Inc, SI4311-B10-GM Datasheet - Page 12
![IC RX FSK 315/434MHZ 20VQFN](/photos/14/11/141117/20-vqfn-b10_sml.jpg)
SI4311-B10-GM
Manufacturer Part Number
SI4311-B10-GM
Description
IC RX FSK 315/434MHZ 20VQFN
Manufacturer
Silicon Laboratories Inc
Series
EZRadio®r
Type
ISM Receiverr
Datasheets
1.SI4311-B10-GM.pdf
(20 pages)
2.SI4311-B10-GM.pdf
(2 pages)
3.SI4311-B10-GM.pdf
(20 pages)
Specifications of SI4311-B10-GM
Package / Case
20-VQFN
Frequency
315MHz, 434MHz
Sensitivity
-104dBm
Data Rate - Maximum
10 kBaud
Modulation Or Protocol
FSK
Applications
Garage Openers, RKE, Security Alarms
Data Interface
PCB, Surface Mount
Antenna Connector
PCB, Surface Mount
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Operating Frequency
315 MHz to 434 MHz
Operating Supply Voltage
2.7 V to 3.6 V
Maximum Operating Temperature
+ 95 C
Minimum Operating Temperature
- 45 C
Mounting Style
SMD/SMT
Supply Current
20 mA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
Memory Size
-
Current - Receiving
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1976-5
Si 4311
3.7. Low Noise Amplifier Input Circuit
Figure 2 shows the typical application circuit with 50 matching. Components C3 and L1 are used to transform the
input impedance of the LNA. C3 is equal to 15 pF and L1 is equal to 33 nH at 433.92 MHz and 62 nH at 315 MHz
for 50 matching.
3.8. Crystal Oscillator
An on-board crystal oscillator is used to generate a 16 MHz reference clock for the Si4311. This reference
frequency is required for proper operation of the Si4311 and is used for calibration of the on-chip VCO and other
timing references. No external load capacitors are required to set the 16 MHz reference frequency if the
recommended crystal load capacitor is around 14 pF, assuming the effective board capacitance between pins
XTL1 and XTL2 is 3 pF and the chip input capacitance on pins XTL1 or XTL2 is 11 pF. Refer to Table 6, “Crystal
Characteristics,” on page 7 for board capacitance and frequency tolerance information. The frequency tolerance of
the crystal should be chosen such that the received signal is within the IF bandwidth of the Si4311 receiver.
Additionally, the Si4311 can be driven by an external 16 MHz reference clock. The clock signal can be applied to
either the XTL1 or XTL2 inputs. When the 16 MHz reference clock is applied to one of the inputs, the other crystal
input pin must be floating.
3.9. Reset Pin
Driving the RST pin (pin 4) low will disable the Si4311 and place the device into reset mode. All active blocks in the
device are powered off in this mode, bringing the current consumption to <10 uA. The Si4311 is enabled by driving
the RST pin (pin 4) to VDD. Refer to Table 4 "Reset Timing Characteristics" for the reset timing requirements. The
chip requires about 320 ms to go from reset to active mode. The Si4311 can output invalid data during the 320 ms
turn-on time.
12
Table 11. AFC Selection Pin 5
Pin 5
0
1
Rev. 0.6
Disable
Enable
AFC