T5743P6-TGQ Atmel, T5743P6-TGQ Datasheet - Page 18
![IC RCVR ASK/FSK 600MHZ 20-SOIC](/photos/6/80/68042/453-20-soic_sml.jpg)
T5743P6-TGQ
Manufacturer Part Number
T5743P6-TGQ
Description
IC RCVR ASK/FSK 600MHZ 20-SOIC
Manufacturer
Atmel
Datasheet
1.T5743P6-TGQ.pdf
(41 pages)
Specifications of T5743P6-TGQ
Frequency
300MHz ~ 450MHz
Sensitivity
-108dBm
Data Rate - Maximum
10 kBaud
Modulation Or Protocol
ASK, FSK
Applications
General Purpose Data Transmission Systems
Current - Receiving
30mA
Data Interface
PCB, Surface Mount
Antenna Connector
PCB, Surface Mount
Voltage - Supply
4.5 V ~ 5.5 V
Operating Temperature
-40°C ~ 105°C
Package / Case
20-SOIC (0.300", 7.50mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Features
-
Memory Size
-
Other names
T5743P6-TGQTR
Figure 21. Activating the Receiving Mode via Pin POLLING/_ON
Data Clock
18
T5743
IC_ACTIVE
POLLING/_ON
Data_out (DATA)
Serial bi-directional
data line
Figure 20 illustrates how to set the receiver back to polling mode via Pin POLLING/_ON.
The Pin POLLING/_ON must be held to low for the time period t
edge on Pin POLLING/_ON and the delay t
time T
This command is faster than using Pin DATA at the cost of an additional connection to
the microcontroller.
Figure 21 illustrates how to set the receiver to receiving mode via the Pin POLL-
ING/_ON. The Pin POLLING/_ON must be held to Low. After the delay t
changes from sleep mode to start-up mode regardless the programmed values for T
and N
check
If the receiver is polled exclusively by a microcontroller, T
31 (permanent sleep mode). In this case the receiver remains in sleep mode as long as
POLLING/_ON is held to High.
The Pin DATA_CLK makes a data shift clock available to sample the data stream into a
shift register. Using this data clock, a microcontroller can easily synchronize the data
stream. This clock can only be used for Manchester and Bi-phase coded signals.
Generation of the data clock:
After a successful bit check, the receiver switches from polling mode to receiving mode
and the data stream is available at Pin DATA. In receiving mode, the data clock control
logic (Manchester/Bi-phase demodulator) is active and examines the incoming data
stream. This is done, like in the bit check, by subsequent time frame checks where the
distance between two edges is continuously compared to a programmable time window.
As illustrated in Figure 22, only two distances between two edges in Manchester and Bi-
phase coded signals are valid (T and 2T).
The limits for T are the same as used for the bit check. They can be programmed in the
LIMIT-register (Lim_min and Lim_max, see Table 11 and Table 12).
The limits for 2T are calculated as follows:
Lower limit of 2T: Lim_min_2T =
Upper limit of 2T: Lim_max_2T=
(If the result for “Lim_min_2T” or “Lim_max_2T” is not an integer value, it will be round
up.)
Sleep mode
will be ignored, but not deleted (see also section “Digital Noise Suppression”).
Sleep
Bit-check
elapses.
. As long as POLLING/_ON is held to Low, the values for T
t
on1
Start-up mode
(Lim_min + Lim_max) - (Lim_max - Lim_min)/2
(Lim_min + Lim_max) + (Lim_max - Lim_min)/2
on3
, the polling mode is active and the sleep
Receiving mode
Sleep
X
X
must be programmed to
on2
. After the positive
on1
Sleep
4569A–RKE–12/02
, the receiver
and N
Sleep
Bit-