CMD-HHCP-315 Linx Technologies Inc, CMD-HHCP-315 Datasheet - Page 3
![XMITTER HANDHELD 315MHZ 8 BUTTON](/photos/14/16/141635/cmd-hhcp_series_sml.jpg)
CMD-HHCP-315
Manufacturer Part Number
CMD-HHCP-315
Description
XMITTER HANDHELD 315MHZ 8 BUTTON
Manufacturer
Linx Technologies Inc
Datasheet
1.CMD-HHCP-418.pdf
(5 pages)
Specifications of CMD-HHCP-315
Function
Transmitter
Modulation Or Protocol
ASK, OOK
Frequency
315MHz
Applications
General Remote Control, Garage Opener, RKE
Interface
Handheld, 8 Button
Data Rate - Maximum
1.2 kbps
Features
8 Buttons, 1000 ft. Operating Distance
Voltage - Supply
2.1 V ~ 3.6 V
Package / Case
Handheld Transmitter
Board Size
71.4 mm x 41.1 mm x 15.2 mm
Minimum Operating Temperature
- 40 C
Supply Voltage (min)
2.1 V
Product
RF Modules
Maximum Frequency
315 MHz
Supply Voltage (max)
3.6 V
Maximum Operating Temperature
+ 85 C
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Power - Output
-
Sensitivity
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
CONTENTION CONSIDERATIONS
BATTERY REPLACEMENT
ASSEMBLY DIAGRAM
Figure 5: CMD-HHCP-*** Assembly
Page 4
It is important to understand that only one transmitter at a time can be activated
within a reception area. While the transmitted signal consists of encoded digital
data, only one carrier of any particular frequency can occupy airspace without
contention at any given time. If two transmitters are activated in the same area
at the same time, then the signals will interfere with each other and the decoder
will not see a valid transmission, so it will not take any action.
The remote unit utilizes a standard CR2032 lithium
button cell. In normal use, it will provide 1 to 2 years of
operation. To replace the battery, remove the access
cover by pressing down firmly on the label area and
sliding it off. Once the unit is open, remove the battery
by sliding it from beneath the holder.
There may be the risk of explosion if the battery is
replaced by the wrong type. Replace it with the same
type of battery while observing the polarity shown in
the adjacent figure.
Figure 4: Battery Access
Battery Access
+
COMPLIANCE REQUIREMENTS
LABELING / INSTRUCTION REQUIREMENTS
Place the above statement in the instruction manual or insert card.
INSTRUCTION TO THE USER
This device complies with Part 15 of the FCC Rules.
Operation of this device is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a Class B
computing device, pursuant to FCC Rules. In order to maintain compliance with
FCC regulations, shielded cables must be used with this equipment. Operation
with non-approved equipment or unshielded cables is likely to result in
interference to radio and TV reception. The user is cautioned that changes and
modifications made to the equipment without the approval of manufacturer
could void the user’s authority to operate this equipment.
The CMD-HHCP-*** has been pre-certified by Linx Technologies for FCC Part
15 and Industry Canada RSP-100 compliance. The 433.92MHz version has also
been tested for CE compliance for use in the European Union. The 315MHz and
418MHz versions are not legal for use in Europe.
The CMD-HHCP-*** Compact Handheld transmitter has already been labeled in
accordance with FCC, Industry Canada, and CE regulations in effect as of the
date of this document. No further labeling of the unit is needed; however, it is
necessary to include the following statement in the end product’s instruction
manual or insert card for FCC compliance. Industry Canada only requires the
shaded portion. EU does not require a statement.
Page 5