X09-019PKC-RA Digi International/Maxstream, X09-019PKC-RA Datasheet - Page 32
![no-image](/images/no-image-200.jpg)
X09-019PKC-RA
Manufacturer Part Number
X09-019PKC-RA
Description
MOD RF 900MHZ 19.2K RS232/485
Manufacturer
Digi International/Maxstream
Series
XStream™r
Specifications of X09-019PKC-RA
Function
Transceiver, Modem
Modulation Or Protocol
FHSS
Frequency
902MHz ~ 928MHz
Applications
General Purpose
Interface
RS-232, RS-485
Sensitivity
-110dBm
Power - Output
20dBm
Data Rate - Maximum
20 kbps
Voltage - Supply
5V
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
© 2006 MaxStream, Inc. Confidential & Proprietary
XStream‐PKG‐R™ RS‐232/485 RF Modem – Product Manual v5.x00 [2006.02.24]
LH (Wake-up Initializer Timer) Command
MD (RF Mode) Command
MK (Address Mask) Command
<Sleep (Low Power)> LH Command adjusts the
duration of time for which the RF initializer is
sent. When receiving modems are put into Cyclic
Sleep Mode, they power-down after a period of
inactivity [specified by ST (Time before Sleep)
command] and will periodically awaken and listen
for transmitted data. In order for the receiving
modems to remain awake, they must detect
~35ms of the wake-up initializer.
LH Command must be used whenever a receiver
is operating in Cyclic Sleep Mode. This lengthens the Wake-up Initializer to a specific amount of
time (in tenths of a second). The Wake-up Initializer Time must be longer than the cyclic sleep
time that is determined by SM (Sleep Mode) Command. If the wake-up initializer time were less
than the Cyclic Sleep interval, the connection would be at risk of missing the wake-up initializer
transmission.
Refer to the figures in the Sleep Mode section [p16] to view diagrams of correct and incorrect
configurations. The images help visualize the importance that the LH value be greater than the
SM cyclic sleep value.
<Networking & Security> The MD command is
used to select/read the RF Mode (Peer-to-peer,
Multi-Stream or Repeater Modes) of the modem.
Multi-Streaming Mode enables exclusive
connections in point-to-multipoint networks.
Refer to the Multi-Streaming Mode section [p48]
for more information regarding how these
parameter values affect other parameter values.
Repeater Mode enables longer range via an
intermediary modem. When MD=3, the modem
will act as a “store and forward” repeater. Any
packets not addressed to this node will be
repeated. A Repeater End Node (MD=4) handles
repeated messages, but will not forward the data
over-the-air. Refer to the Repeater Mode section
[p43] for more information.
<Networking> MK Command is used to set/read
the Address Mask.
All data packets contain the Destination Address
of the transmitting modem. When an RF data
packet is received, the transmitter’s Destination
Address is logically “ANDed” (bitwise) with the
Address Mask of the receiver. The resulting value
must match the Destination Address or the
Address Mask of the receiver for the packet to be
received and sent out the modem’s DO serial
port. If the “ANDed” value does not match either
the Destination Address or the Address Mask of
the receiver, the packet is discarded. (All “0”
values are treated as “irrelevant” values and are ignored.)
AT Command: ATMD
Binary Command: 0x32 (50 decimal)
Parameter Range: 0 – 4
Default Parameter Value: 0
Number of bytes returned: 1
Related Commands: CB (Connection Duration
Timeout), CE (Connection Inactivity Timeout),
CM (Connection Message), DC (Disconnect)
Minimum Firmware Version Required: 4.30
AT Command: ATLH
Binary Command: 0x0C (12 decimal)
Parameter Range: 0 – 0xFF
Default Parameter Value: 1
Number of bytes returned: 1
Related Commands: HT (Time before Wake-up
Initializer), SM (Sleep Mode), ST (Time before
Sleep)
AT Command: ATMK
Binary Command: 0x12 (18 decimal)
Parameter Range: 0 – 0xFFFF
Default Parameter Value: 0xFFFF
(Destination address (DT parameter) of the
transmitting modem must exactly match the
destination address of the receiving modem.)
Number of bytes returned: 2
Related Commands: DT (Destination Address),
HP (Hopping Channel), ID (Modem VID), MY
(Source Address)
Parameter
0
1
2
3
4
[x 100 milliseconds]
Peer-to-Peer (Transparent)
Multi-Stream Remote
Repeater End Node
Multi-Stream Base
Configuration
Repeater
32