X24-009PKC-RA Digi International/Maxstream, X24-009PKC-RA Datasheet - Page 33
![no-image](/images/no-image-200.jpg)
X24-009PKC-RA
Manufacturer Part Number
X24-009PKC-RA
Description
MOD RF 2.4GHZ 9600BPS RS232/485
Manufacturer
Digi International/Maxstream
Series
XStream™r
Specifications of X24-009PKC-RA
Function
Transceiver, Modem
Modulation Or Protocol
FHSS
Frequency
2.4GHz ~ 2.4835GHz
Applications
General Purpose
Interface
RS-232, RS-485
Sensitivity
-110dBm
Power - Output
17dBm (50mW)
Data Rate - Maximum
20 kbps
Voltage - Supply
5V
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
© 2006 MaxStream, Inc. Confidential & Proprietary
XStream‐PKG‐R™ RS‐232/485 RF Modem – Product Manual v5.x00 [2006.02.24]
MY (Source Address) Command
NB (Parity) Command
PC (Power-up Mode) Command
PK (RF Packet Size) Command
<Networking & Security> Set/Read the source
address of the modem.
Refer to the Addressing section [p41] of the RF
Communication Modes chapter for more
information.
<Serial Interfacing> Select/Read parity settings
for UART communications.
<Command Mode Options> PC Command allows
the modem to power-up directly into AT
Command Mode from reset or power-on. If PC
Command is enabled with SM Parameter set to 1,
the DI3 Pin (SLEEP) can be used to enter the
modem into AT Command Mode. When the DI3
pin is de-asserted (low), the modem will Wake-up
into AT Command Mode. This behavior allows
modem DTR emulation.
<Serial Interfacing> Set/Read the maximum size
of the RF packets sent out a transmitting
modem. The maximum packet size can be used
along with the RB and RO parameters to
implicitly set the channel dwell time.
Changes to this parameter may have a
secondary effect on the RB (Packet Control
Characters) parameter. RB must always be less
than or equal to PK. If PK is changed to a value
less than the current value of RB, RB is automatically lowered to be equal to PK.
AT Command: ATMY
Binary Command: 0x2A (42 decimal)
Parameter Range: 0 – 0xFFFF
Default Parameter Value: 0xFFFF (Disabled –
the DT (Destination Address) parameter serves
as both source and destination address.)
Number of bytes returned: 2
Related Commands: DT (Destination Address),
HP (Hopping Channel), ID (Modem VID), MK
(Address Mask), AM (Auto-set MY)
Minimum Firmware Version Required: 4.30
AT Command: ATPK
Binary Command: 0x29 (41 decimal)
Parameter Range: 0 – 0x100 [Bytes]
Default Parameter Value: 0x40 (64 decimal)
Number of bytes returned: 2
Related Commands: RB (Packetization
Threshold), RO (Packetization Timeout)
Minimum Firmware Version Required: 4.30
AT Command: ATNB
Binary Command: 0x23 (35 decimal)
Parameter Range: 0 – 4
Default Parameter Value: 0
Number of bytes returned: 1
Minimum Firmware Version Required: 4.27B
AT Command: ATPC
Binary Command: 0x1E (30 decimal)
Parameter Range: 0 – 1
Default Parameter Value: 0
Number of bytes returned: 1
Minimum Firmware Version Required: 4.22
Parameter
Parameter
0
1
2
3
4
0
1
Power-up to Idle Mode
AT Command Mode
8-bit (no parity or
7-bit (any parity)
Configuration
Configuration
Power-up to
8-bit space
8-bit mark
8-bit even
8-bit odd
33