X24-019PKC-RA Digi International/Maxstream, X24-019PKC-RA Datasheet - Page 34
![no-image](/images/no-image-200.jpg)
X24-019PKC-RA
Manufacturer Part Number
X24-019PKC-RA
Description
MOD RF 2.4GHZ 19.2K RS232/485
Manufacturer
Digi International/Maxstream
Series
XStream™r
Specifications of X24-019PKC-RA
Function
Transceiver, Modem
Modulation Or Protocol
FHSS
Frequency
2.4GHz ~ 2.4835GHz
Applications
General Purpose
Interface
RS-232, RS-485
Sensitivity
-102dBm
Power - Output
17dBm (50mW)
Data Rate - Maximum
20 kbps
Voltage - Supply
5V
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
© 2006 MaxStream, Inc. Confidential & Proprietary
XStream‐PKG‐R™ RS‐232/485 RF Modem – Product Manual v5.x00 [2006.02.24]
PW (Pin Wake-up) Command
RB (Packetization Threshold) Command
RE (Restore Defaults) Command
RN (Delay Slots) Command
<Sleep (Low Power)> Under normal operation, a
modem in Cyclic Sleep Mode cycles from an
active state to a low-power state at regular
intervals until data is ready to be received. If the
PW Parameter is set to 1, the SLEEP/DI3 Pin can
be used to awaken the modem from Cyclic Sleep.
If the SLEEP Pin is de-asserted (low), the modem
will be fully operational and will not go into Cyclic
Sleep. Once SLEEP is asserted, the modem will
remain active for the period of time specified by
ST (Time before Sleep) Command, and will return
to Cyclic Sleep Mode (if no data is ready to be
transmitted). PW Command is only valid if Cyclic
Sleep has been enabled.
<Serial Interfacing> RF transmission will
commence when data is in the DI Buffer and
either of the following criteria are met:
If PK is lowered below the value of RB; RB is
automatically lowered to match PK.
Note: RB and RO criteria only apply to the first
packet of a multi-packet transmission. If data remains in the DI Buffer after the first packet,
transmissions will continue in streaming manner until there is no data left in the DI Buffer (UART
receive buffer).
<Diagnostics> RE Command restores all
configurable parameters to factory default
settings. However, the RE Command will not
write the default values to non-volatile (persistent) memory. Unless the WR (Write) Command is
issued after the RE command, the default settings will not be saved in the event of modem reset
or power-down.
<Networking> RN Command is only applicable if
retries have been enabled [RR (Retries)
command], or if forced delays will be inserted
into a transmission [refer to TT (Streaming Limit)
command]. RN Command is used to adjust the
time delay that the transmitter inserts before
attempting to resend a packet. If the transmitter
fails to receive an acknowledgement after
sending a packet, it will insert a random number
of delay slots (ranging from 0 to (RN minus 1))
before attempting to resend the packet. Each
delay slot lasts for a period of 38ms.
If two modems attempted to transmit at the same time, the random time delay after packet
failure would allow one of the two modems to transmit the packet successfully, while the other
would wait until the channel opens up to begin transmission.
• RO times out on the UART receive lines
• RB characters have been received by the
(ignored if RO = 0)
UART (ignored if RB = 0)
AT Command: ATRB
Binary Command: 0x20 (32 decimal)
Parameter Range: 0 – 0x100 [bytes]
(Maximum value equals the current value of PK
Parameter (up to 0x100 HEX (800 decimal))
Default Parameter Value: 1
Number of bytes returned: 2
Related Commands: PK (RF Packet Size), RO
(Packetization Timeout)
Minimum Firmware Version Required: 4.30
AT Command: ATPW
Binary Command: 0x1D (29 decimal)
Parameter Range: 0 – 1
Default Parameter Value: 0
Number of bytes returned: 1
Related Commands: SM (Sleep Mode), ST (Time
before Sleep)
Minimum Firmware Version Required: 4.22
AT Command: ATRE
Binary Command: 0x0E (14 decimal)
AT Command: ATRN
Binary Command: 0x19 (25 decimal)
Parameter Range: 0 – 0xFF [slots]
Default Parameter Value: 0 (no delay slots
inserted)
Number of bytes returned: 1
Related Commands: RR (Retries), TT
(Streaming Limit)
Minimum Firmware Version Required: 4.22
Parameter
0
1
Configuration
Disabled
Enabled
34