AD9869BCPZ Analog Devices Inc, AD9869BCPZ Datasheet - Page 24
![IC MXFE ADC 80MSPS TX/RX 64LFCSP](/photos/6/50/65021/505-64-lfcsp_sml.jpg)
AD9869BCPZ
Manufacturer Part Number
AD9869BCPZ
Description
IC MXFE ADC 80MSPS TX/RX 64LFCSP
Manufacturer
Analog Devices Inc
Datasheet
1.AD9869-EBZ.pdf
(36 pages)
Specifications of AD9869BCPZ
Rf Type
HPNA, VDSL
Package / Case
64-LFCSP
Brief Features
Third-order, Programmable Low Pass Filter, Flexible Digital Data Path Interface
Supply Voltage Range
3.135V To 3.465V, 3V To 3.6V
Operating Temperature Range
-40°C To +85°C
Ic Function
Mixed Signal Front End
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
Frequency
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
AD9869
RECEIVE PATH
The receive signal path for the AD9869 (or its related part, the
AD9868) consists of a 3-stage RxPGA, a 3-pole programmable
LPF, and a 12-bit (or 10-bit) ADC (see Figure 24). Note that the
additional two bits of resolution offered by the AD9869 result in
a 3 dB to 5 dB lower noise floor, depending on the RxPGA gain
setting and LPF cutoff frequency. Also working in conjunction with
the receive path is an offset correction circuit. These blocks are
discussed in detail in the following sections. Note that the power
consumption of the RxPGA can be modified via Register 0x13
as discussed in the Power Control and Dissipation section.
RXEN/SYNC
Rx PROGRAMMABLE GAIN AMPLIFIER
The RxPGA has a digitally programmable gain range from
−12 dB to +48 dB with 1 dB resolution via a 6-bit word. Its
purpose is to extend the dynamic range of the Rx path such that
the input of the ADC is presented with a signal that scales
within its fixed 2 V input span. There are multiple ways of
setting the RxPGA gain as discussed in the RxPGA Control
section, as well as an alternative 3-bit gain mapping having a
range of −12 dB to +36 dB with a +8 dB resolution.
The RxPGA is comprised of two sections: a continuous time
PGA (CPGA) for course gain and a switched capacitor PGA
(SPGA) for fine gain resolution. The CPGA consists of two
cascaded gain stages providing a gain range of −12 dB to +42 dB
with a 6 dB resolution. The first stage features a low noise
preamplifier (<3.0 nV/√Hz), thereby eliminating the need for
an external preamplifier. The SPGA provides a gain range of
0 dB to 6 dB with a 1 dB resolution. A look-up table (LUT) is
used to select the appropriate gain setting for each stage.
The nominal differential input impedance of the RxPGA input
appearing at the device RX+ and RX− input pins is 400 Ω||4 pF
(±20%) and remains relatively independent of gain setting.
ADIO[11:6]/
ADIO[5:0]/
PGA[5:0]
Rx[5:0]
Tx[5:0]
RXCLK
PORT
PORT
SPI
6
4
Figure 24. Functional Block Diagram of Rx Path
10/12
REGISTER
CONTROL
80MSPS
ADC
CLK
SYNC.
MAPPING
0 TO 6dB
Δ = 1dB
GAIN
LUT
SPGA
MULTIPLIER
–6 TO 18dB
Δ = 6dB
2
M
CLK
2-POLE
LPF
–6 TO 24dB
Δ = 6dB
AD9869
1-POLE
LPF
CLKOUT1
CLKOUT2
OSCIN
XTAL
RX+
RX–
Rev. 0 | Page 24 of 36
The PGA input is self-biased at a 1.3 V common-mode level, allow-
ing maximum input voltage swings of ±1.5 V at RX+ and RX−.
AC-coupling the input signal to this stage via 0.1 μF coupling
capacitors is recommended to ensure that any external dc offset
does not become amplified with high RxPGA gain settings,
potentially exceeding the ADC input range.
To limit the RxPGA self-induced input offset, an offset cancella-
tion loop is included. This cancellation loop is automatically
performed upon power-up and can also be initiated via the SPI.
During calibration, the RxPGA first stage is internally shorted,
and each gain stage set to a high gain setting. A digital servo
loop slaves a calibration DAC, which forces the Rx input offset
to be within ±32 LSBs for this particular high gain setting.
Although the offset varies for other gain settings, the offset is
typically limited to ±5% of the ADC’s 2 V input span. Note that
the offset cancellation circuitry is intended to reduce the voltage
offset attributed to only the RxPGA input stage, not to any dc
offsets attributed to an external source.
The gain of the RxPGA should be set to minimize clipping of
the ADC while utilizing most of its dynamic range. The maximum
peak-to-peak differential voltage that does not result in ADC
clipping is shown in Figure 25. Although the graph suggests that
the maximum input signal for a gain setting of −12 dB is 8.0 V p-p,
the maximum input voltage into the PGA should be limited to
less than 6 V p-p to prevent turning on ESD protection diodes.
For applications having higher maximum input signals, consider
adding an external resistive attenuator network. While the input
sensitivity of the Rx path is degraded by the amount of attenuation
on a dB-to-dB basis, the low noise characteristics of the RxPGA
provide some design margin such that the external line noise
remains the dominant source.
Figure 25. Maximum Peak-to-Peak Input vs. RxPGA Gain Setting that
8.0000
4.0000
2.0000
1.0000
0.5000
0.2500
0.1250
0.0625
0.0312
0.0156
0.0100
–12
–6
Does Not Result in ADC Clipping
0
6
12
GAIN (dB)
18
24
30
36
42
48