ATAB5423-3-WB Atmel, ATAB5423-3-WB Datasheet - Page 70
![KIT DEMO 315MHZ BLACKBIRD](/photos/14/12/141239/atab5423-3-wb_sml.jpg)
ATAB5423-3-WB
Manufacturer Part Number
ATAB5423-3-WB
Description
KIT DEMO 315MHZ BLACKBIRD
Manufacturer
Atmel
Type
Transceiver, UHFr
Specifications of ATAB5423-3-WB
Frequency
315MHz
Product
RF Modules
For Use With/related Products
ATA5423
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
ATAB-5423-3-WB
12. Electrical Characteristics: General (Continued)
This device is manufactured with an industrial (not automotive) grade process and process controls. Although this device may
meet certain automotive grade criteria in performance, Atmel can not recommend that this device be used in any automotive
application.
All parameters refer to GND and are valid for T
and V
about current consumption, timing and digital pin properties can be found in the specific sections of the “Electrical Characteristics”.
70
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
2.10 System bandwidth
2.11
No. Parameters
2.6
2.7
2.8 System noise figure
2.9 Intermediate frequency
VS2
Maximum frequency
offset in FSK mode
Supported FSK frequency
deviation
System outband
2nd
point with respect to f
= V
1. Pin numbers in brackets mean they were measured with RF_IN matched to 50 according to
ATA5423/ATA5425/ATA5428/ATA5429
-
order input intercept
VAUX
component values according to
with component values according to
= 5.0V (Base
IF
-
station Application). Typical values are given at f
Test Conditions
Maximum frequency
difference of f
between receiver and
transmitter in FSK
mode (f
frequency of the FSK
signal with
f
With up to 2 dB
loss of sensitivity.
Note that the tolerable
frequency offset is for
f
lower than for
f
f
f
f
f
f
f
f
f
f
f
This value is for
information only!
Note that for crystal and
system frequency offset
calculations, f
must be used.
f
DEV
DEV
DEV
RF
RF
RF
RF
RF
RF
RF
RF
RF
RF
IF
f
f
f
OFFSET
meas1
meas2
= f
= 315 MHz
= 345 MHz
= 433.92 MHz
= 868.3 MHz
= 915 MHz
= 315 MHz
= 345 MHz
= 433.92 MHz
= 868.3 MHz
= 915 MHz
= ±22 kHz, 6 kHz
= ±16 kHz hence
= ±16 kHz)
meas2
= 1,800 MHz
= 2,026 MHz
RF
is the center
±52 kHz
Table 3-2 on page 12
–
amb
RF
OFFSET
f
Table 3-7 on page
= 25°C, V
meas1
VS1
Pin
(4)
(4)
(4)
(4)
(4)
(4)
(4)
(4)
(4)
= V
(1)
VS2
and RF_OUT matched to 50 according to
22.
= 3.0V (1
Symbol
f
SBW
OFFSET
IIP2
f
NF
NF
NF
NF
NF
DEV
f
f
f
f
f
IF
IF
IF
IF
IF
-
RF
battery application), V
= 433.92 MHz unless otherwise specified. Details
Min.
–
±14
58
Typ.
10.3
±16
227
235
223
226
238
185
+50
6.0
6.2
7.0
9.7
VS2
= 6.0V (2-battery application)
Figure 3-1 on page 11
Figure 3-10 on page 21
Max.
+58
±22
4841D–WIRE–10/07
dBm
Unit
kHz
kHz
kHz
kHz
kHz
kHz
kHz
kHz
dB
dB
dB
dB
dB
Type*
with
B
B
B
B
B
B
B
A
A
A
A
A
A
C