A09-HASM-675 Digi International/Maxstream, A09-HASM-675 Datasheet - Page 6
![no-image](/images/no-image-200.jpg)
A09-HASM-675
Manufacturer Part Number
A09-HASM-675
Description
ANT 900MHZ 6" R/A JOINT W/RPSMA
Manufacturer
Digi International/Maxstream
Series
A09-HASMr
Specifications of A09-HASM-675
Antenna Type
Whip: 1/2 Wave, Right Angle
Number Of Bands
1
Frequency
915MHz (902MHz ~ 928MHz)
Gain
2.1dBi
Termination
RP-SMA
Mounting Type
Connector
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Vswr
-
Height (max)
-
9XTend™ OEM RF Module ‐ Product Manual v2.x4x [2007.01.04]
Figure 1‐01. XTend OEM RF Module Pin Numbers
Table 1‐03. Pin Signal Descriptions
* RF module has 10K Ω internal pull‐up resistor
Note: When integrating the module with a Host PC board, all lines not used should be left disconnected (floating).
Number
1.3. Pin Signals
12-20
Pin
10
11
1
2
3
4
5
6
7
8
9
RS-485 TX_EN
GPI2 / SLEEP
GPO1 / CTS /
Mnemonic
GPI1 / RTS /
(Low‐asserted signals distinguished with a horizontal line over signal name.)
CONFIG /
TX_PWR
RX LED
GPO2 /
SHDN
CMD
RSSI
GND
VCC
DO
DI
© 2007 MaxStream, Inc.
I/O
O*
O
O
O
O
I*
-
I
I
I
I
I
during Shutdown
High Impedance
yes
yes
yes
yes
yes
yes
yes
no
no
no
-
-
Connect
Must
yes
yes
yes
yes
-
-
-
-
-
-
-
-
reserved / do not connect
Ground
Power: 2.8 - 5.5 VDC
General Purpose Output 2: <Default (CD=2)> Pin is driven low. Refer to the CD
Command [p24] for other configuration options.
RX LED: Pin is driven high during RF data reception; otherwise, the pin is driven
low. Refer to the CD Command [p24] to enable.
Transmit_Power: Pin pulses low during RF transmission; otherwise, the pin is
driven high to indicate power is on and the module is not in Sleep or Shutdown
Mode.
Data In: Serial data entering the module (from the UART host). Refer to the Serial
Communications [p9] section for more information.
Data Out: Serial Data exiting the module (to the UART host). Refer to the Serial
Communications [p9] section for more information.
Shutdown: Pin is driven high during operation and low during Shutdown.
Shutdown enables the lowest power mode (~5 µA) available to the module. Refer
to the Shutdown Mode [p14] section for more information.
General Purpose Input 2: reserved for future use
SLEEP: By default, SLEEP is not used. To configure this pin to enable Sleep
Modes, refer to the Sleep Mode [p15], SM Command [p37] & PW Command [p32]
sections.
General Purpose Output 1: reserved for future use
CTS (Clear-to-Send): <Default (CS=0)> When pin is driven low, the UART host
is permitted to send serial data to the module. Refer to the Serial Communications
[p9] & CS Command [p25] sections for more information.
RS-485 Transmit Enable: To configure this pin to enable RS-485 half and full-
duplex communications. Refer to the Serial Communications [p9] & CS Command
[p25] sections.
General Purpose Input 1: reserved for future use
RTS (Request-to-Send): By default, is not used. To configure this pin to
regulate the flow of serial data exiting the module, refer to the Serial
Communications [p9] & RT Command [p36] sections.
CMD (Command): By default, CMD is not used. To configure this pin to enable
binary command programming, refer to the Binary Commands [p18] & RT
Command [p36] sections.
Configuration: Pin can be used as a backup method for entering Command
Mode during power-up. Refer to the Command Mode [p17] section for more
information.
Receive Signal Strength Indicator: By default, pin is used as an RSSI PWM
output after at the conclusion of the power-up sequence. Refer to the RP
Command [p35] for more information.
Chapter 1 ‐ 9XTend OEM RF Module
Function
6