MGA-83563-BLKG Avago Technologies US Inc., MGA-83563-BLKG Datasheet - Page 18
![no-image](/images/manufacturer_photos/0/0/86/avago_technologies_us_inc__sml.jpg)
MGA-83563-BLKG
Manufacturer Part Number
MGA-83563-BLKG
Description
IC RF AMP GAAS 3V 22DBM
Manufacturer
Avago Technologies US Inc.
Type
Power Amplifierr
Datasheet
1.MGA-83563-BLKG.pdf
(22 pages)
Specifications of MGA-83563-BLKG
P1db
19.7dBm
Package / Case
SC-70-6, SC-88, SOT-363
Current - Supply
152mA ~ 200mA
Frequency
500MHz ~ 6GHz
Gain
23dB
Test Frequency
2GHz
Voltage - Supply
2.7V ~ 3.6V
Mounting Style
SMD/SMT
Technology
Power Amplifier
Number Of Channels
1
Operating Frequency
6000 MHz
Operating Supply Voltage
3 V
Supply Current
200 mA @ 3 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Rf Type
-
Noise Figure
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
516-1956
MGA-83563-BLKG
MGA-83563-BLKG
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MGA-83563-BLKG
Manufacturer:
AVAGO/安华高
Quantity:
20 000
18
Hints and Troubleshooting
Oscillation
Unconditional stability of the MGA-83563 is dependent
on having good grounding. Inadequate device ground-
ing or poor PCB layout techniques could cause the device
to be potentially unstable. In a multistage RFIC such as
the MGA-83563, feedback through bias lines supplying
voltage to both stages can lead to oscillation. It is im-
portant to well bypass the connections to bias supply to
ensure stable operation.
Statistical Parameters
Several categories of parameters appear within this data
sheet. Parameters may be described with values that are
either “minimum or maximum, ” “typical, ” or “standard de-
viations. ”
The values for parameters are based on comprehensive
product characterization data, in which automated mea-
surements are made on of a minimum of 500 parts taken
from three non-consecutive process lots of semiconduc-
tor wafers. The data derived from product characteriza-
tion tends to be normally distributed, e.g., fits the stan-
dard bell curve.
Parameters considered to be the most important to system
performance are bounded by minimum or maximum
values. For the MGA-83563, these parameters are: Saturat-
ed Output Power (P
Device Current (I
100% tested as part of the manufacturing process.
Figure 41. Output Power vs. Supply Voltage for the 900 MHz Amplifier.
26.00
24.00
22.00
20.00
18.00
16.00
14.00
12.00
1.5
d
2.0
). Each of the guaranteed parameters is
sat
P
P
sat
), Power Added Efficiency (PAE), and
1dB
SUPPLY VOLTAGE, V
2.5
d
(V)
3.0
3.5
Values for most of the parameters in the table of Electri-
cal Specifications that are described by typical data are
the mathematical mean (P), of the normal distribution
taken from the characterization data. For parameters
where measurements or mathematical averaging may
not be practical, such as S-parameters or Noise Param-
eters and the performance curves, the data represents a
nominal part taken from the center of the characteriza-
tion distribution. Typical values are intended to be used
as a basis for electrical design.
To assist designers in optimizing not only the immedi-
ate amplifier circuit using the MGA-83563, but to also
evaluate and optimize trade-offs that affect a complete
wireless system, the standard deviation (V) is provided
for many of the Electrical Specifications parameters (at
25°C) in addition to the mean. The standard deviation is
a measure of the variability about the mean. It will be re-
called that a normal distribution is completely described
by the mean and standard deviation.
Standard statistics tables or calculations provide the
probability of a parameter falling between any two
values, usually symmetrically located about the mean.
Referring to Figure 42 for example, the probability of a
parameter being between ±1V is 68.3%; between ±2V is
95.4%; and between ±3V is 99.7%.
Figure 42. Normal Distribution.
Phase Reference Planes
The positions of the reference planes used to specify S-
parameters and Noise Parameters for the MGA-83563 are
shown in Figure 43. As seen in the illustration, the refer-
ence planes are located at the point where the package
leads contact the test circuit.
Figure 43. Phase Reference Planes.
-3σ
-2σ
TEST CIRCUIT
REFERENCE
-1σ
PLANES
Parameter Value
68%
95%
99%
Mean (μ)
(typical)
+1σ +2σ +3σ