ZB2430-Q-E-S-U-EVB Laird Technologies, ZB2430-Q-E-S-U-EVB Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/3/378/laird_technologies_sml.jpg)
ZB2430-Q-E-S-U-EVB
Manufacturer Part Number
ZB2430-Q-E-S-U-EVB
Description
KIT BOARD EXTRA ZB2430-Q-E-S-U
Manufacturer
Laird Technologies
Series
ZigBee™ Your Way™ AeroCommr
Type
802.15.4/Zigbeer
Datasheet
1.ZB2430-D-C-S-A-EVB.pdf
(62 pages)
Specifications of ZB2430-Q-E-S-U-EVB
Contents
Board
For Use With/related Products
SDK-ZB2430-Q
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
4
S P E C I F I C A T I O N S
P I N D E F I N I T I O N S
The ZB2430 has a simple interface that allows OEM Host communications with the transceiver. Table 2 below shows
the connector pin numbers and associated functions.
SMT Pin
10
11
12
13
14
15
16
17
1
2
3
4
5
6
7
8
9
Pluggable
Pin
19
10
18
11
20
16
T a b l e 2 : P i n D e f i n i t i o n s f o r t h e Z B 2 4 3 0 t r a n s c e i v e r
4
6
8
7
3
2
1
9
5
-
-
Type
GND
PWR
PWR
GND
I/O
O
O
O
O
I
I
I
I
I
I
I
Signal Name
Do not Connect
Test / Sleep Int.
GI0_2/ DE-RE
GIO_3 / AD_0
GIO_4 / AD_1
CMD/Data
UP_Reset
In Range
GIO_0
GIO_1
GND
GND
RXD
VCC
TXD
VPA
RTS
Generic Output Pin
Generic Output Pin
Has internal connection, for Aerocomm use only.
Generic Input pin
Has Internal connection. Reserved for future GPIO.
Asynchronous serial data input to transceiver
Asynchronous serial data output from transceiver
Signal Ground
3.0 - 3.5 V ±50mV ripple (must be connected)
3.0 - 3.5 V ±50mV ripple (must be connected)
Signal Ground
Test Mode – When pulled logic Low and then applying power or resetting, the
transceiver’s serial interface is forced to a 9600, 8-N-1 rate. To exit Test mode,
the transceiver must be reset or power-cycled with Test Mode pulled logic
High or disconnected
Note: Because this mode disables some modes of operation, it should not be
permanently pulled Low during normal operation.
Sleep mode interrupt - When logic Low, forces End Device to wake up from
sleep mode. When logic High, allows End Device to sleep and wake-up
according to specified poll rate. Sleep mode interrupt function available on
End Devices only.
Has Internal connection. Reserved for future GPIO.
RESET – Controlled by the ZB2430 for power-on reset if left unconnected.
After a stable power-on reset, a logic Low pulse will reset the transceiver.
When logic Low, the transceiver interprets OEM Host data as command data.
When logic High or floating, the transceiver interprets OEM Host data as trans-
mit data.
When logic Low, the transceiver is associated with a parent and has been
assigned a 16-bit Network Address. The Coordinator will report In Range after
selecting a clear channel to operate.
Request to Send – When enabled in EEPROM, the OEM Host can take this
High when it is not ready to accept data from the transceiver. NOTE: Keeping
RTS High for too long can cause data loss due to buffer overflow.
Function
1
2