CRB2A4E161GT AVX Corporation, CRB2A4E161GT Datasheet - Page 4

• Manufacturer Part Number: CRB2A4E161GT
• Description: RES ARRAY 160 OHM 2% 0804
• Manufacturer: AVX Corporation
• Series: CRB, Kyocerar

Specifications of CRB2A4E161GT

• Resistance (ohms): 160
• Number Of Resistors: 4
• Circuit Type: Isolated
• Temperature Coefficient: ±250ppm/°C
• Tolerance: ±2%
• Power Per Element: 62.5mW
• Number Of Pins: 8
• Package / Case: 0804 (2010 Metric), Concave
• Size / Dimension: 0.079" L x 0.039" W (2.00mm x 1.00mm)
• Height: 0.016" (0.40mm)
• Mounting Type: Surface Mount
• Operating Temperature: -55°C ~ 125°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Mechanical Characteristics
Environmental Characteristics
Soldering Heat
Anti-Vibration
Temperature
Temperature
Temperature
Loading Life
Resistance
Resistance
in Moisture
Resistance
Moisture
Terminal
Strength
Life Test
Storage
Storage
Test Conditions and Standards
CRB, CRC Series
Solvent
Cycle
High
Low
Test
Solderability
Item
Item
Visual
Visual
Visual
Visual
Visual
Visual
Visual
Visual
Visual
Visual
DR/ R
DR/ R
DR/ R
DR/ R
DR/ R
DR/ R
DR/ R
DR/ R
DR/ R
DR/ R
± (0.5%+0.05W) max.
± (1%+0.05W) max.
± (1%+0.05W) max.
± (1%+0.05W) max.
No evidence of mechanical damage after loading
± (1%+0.1W) max.
± (2%+0.1W) max.
± (3%+0.1W) max.
± (3%+0.1W) max.
± (3%+0.1W) max.
± (3%+0.1W) max.
of the initial value
of the initial value
of the initial value
of the initial value
of the initial value
of the initial value
of the initial value
of the initial value
of the initial value
of the initial value
Resistor
Resistor
Coverage≥95% each termination end
No evidence of mechanical damage
No evidence of mechanical damage
No evidence of mechanical damage
No evidence of mechanical damage
No evidence of mechanical damage
No evidence of mechanical damage
No evidence of mechanical damage
No evidence of mechanical damage
No evidence of leaching
Standard
Standard
50mW max.
50mW max.
50mW max.
50mW max.
50mW max.
50mW max.
50mW max.
50mW max.
50mW max.
50mW max.
Jumper
Jumper
Apply the load as show:
Measure resistance during load application
PC board: Glass epoxy t=1.6
Immerse into molten solder at 260±5°C for 10±1 sec.
Stabillize component at room temperature for 1hr.
Measure resistance.
Immerse in Rogin Flux for 2±0.5 sec. and in
SN62 solder at 235±5°C for 2±0.5 sec.
2 hrs. each in X, Y and Z axis. (TTL 6hrs.) 10 to 55 Hz
sweep in 1 min. at 1.5mm amplitude.
Immerse in static state butyl acetate at 20°C to 25°C
for 30±5 sec.
Stabillize component at room temperature for 30 min.
then measure value.
1) Run 5 cycles as follows: −55±3°C for 30 min.
2) Stabilize component at room temperature for 1hr.
1) Dwell in −55°C chamber without loading for
2) Stabilize component at room temperature for 1hr.
1) Dwell in 125°C chamber without loading for
2) Stabilize component at room temperature for 1hr.
1) Dwell in temp.: 65°C RH90 to 95%RH chamber
2) Stabilize component at room temperature for 1hr.
1) Temp.: 70±3°C Voltage: (rated voltage) on 90 min.
2) Stabilize component at room temperature for 1hr.
1) Temp.: 40±2°C RH: 90 to 95% Voltage Cycle: on 90
2) Stabilize component at room temperature for 1hr.
125±3°C for 30 min. Room temp. for 10 to 15 min.
then measure value.
1000
then measure value.
1000
then measure value.
without loading for 1000
then measure value.
off 30 min. Duration: 1000
then measure value.
min. (rated voltage) off 30 min. Duration: 1000
then measure value.
+48
−0
Resistor
Resistor
+48
−0
hrs.
hrs.
Test Conditions
Test Conditions
+48
−0
hrs.
+48
−0
hrs.
Jumper
Jumper
+48
−0
hrs.